All times are UTC - 5 hours [ DST ]


Forum rules


No new topics are allowed in this forum. Please use other forums to create topics.



Post new topic Reply to topic  [ 97 posts ]  Go to page Previous  1, 2, 3, 4, 5
Author Message
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: May 9th, 2008, 10:30 
Offline

Joined: August 25th, 2007, 1:24
Posts: 297
Location: Western Australia, Australia
Rameez, Can you suggest anyplace where i can buy some of these 'smooth' chips? I often need them for Maxtor and WD drives with burnt motor controller chips.

Thanks.


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: January 31st, 2010, 14:52 
Offline

Joined: January 31st, 2010, 14:42
Posts: 5
Location: Belgium
Hi everyone!

I have a fried DiamondMax Plus 9 200GB ATA 133 (disks not spinning at all)
YAR41BW0 Firmware F8FYA

I tried to swap with a pcb of a DiamondMax Plus 9 80GB ATA 133 but with another firmware version
The fried disk now is "alive", it starts spinning but after let's say 10-20 seconds it starts to click and Bios doesn't recognize it at all

So I restored the working pcb back to its orginal owner (the 80GB one) and it worked, this pcb has not been damaged.

Does this mean I have no preamp problems with the dead hard disk and should only be a pcb problem?
Just to know, since I already ordered a new matching pcb

Thanx!
Pietro


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: January 31st, 2010, 14:57 
Offline
User avatar

Joined: March 28th, 2008, 7:52
Posts: 1466
Location: Europe, Hungary
Hi

This test doesn't shows exactly your preamp's condition.
If you want to get a compatible pcb, you should match this:

F8FYA + the 4 letter code on the top lid.

No more needed.
If your drive still clicking, then the preamp is dead.

Janos


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 1st, 2010, 4:01 
Offline

Joined: January 31st, 2010, 14:42
Posts: 5
Location: Belgium
Sorry for my noob question but I AM a noob with HDs...

I'm worried about the reason why my HD looks dead. If I have any chance to recover data.
This is exactly what happened...
I wrongly plugged the power connector, and 'till that moment the disk was fully functionally
After that, platters didn't spin anymore, so I thought about a power fault.

I swapped the pcb, but I don't remember the firmware version, so I can't confirm right now if it was compatible or not.
By the way platters started to spin again, with bad click noises, but not fast repeating clicks.

I read lots of post but I preferred to directly show my issue.
Can a power failure like mine damage head and/or preamp? HD was fully functionally before I wrongly connected the power molex.
I'm scared of the click of death O_O

Thanx thanx thanx


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 1st, 2010, 4:38 
Offline

Joined: October 3rd, 2005, 0:40
Posts: 4301
Location: Hungary
Hi,

yes, in your case it is highly probable that preamp is dead since when you pluged the power connector reversed(if it is what you meant by 'wrongly'), the preamp received 12V instead of 5V alimentation and this causes fatal damage surely.
If the data is important you should stop DIY right now and take it to a pro.

pepe

_________________
Adatmentés - Data recovery


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 1st, 2010, 5:36 
Offline

Joined: January 31st, 2010, 14:42
Posts: 5
Location: Belgium
exactly, as you said, I meant reversed.
I thought there was some kind of protection circuit which prevents damage to the inner circuits.
I'll prepare a grave for my poor HD

thank you guys for your help


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 5th, 2010, 6:16 
Offline

Joined: January 31st, 2010, 14:42
Posts: 5
Location: Belgium
Yesterday I gave a try swapping 2 not compatible PCBs between 2 Maxtor DiamondMax Plus 10

Donor (the working one)
6L200M0
BANC1G10
F/W: R3GLA
SABRE/ROHS

Receiver (with spinning platters only, head doesn't move at all, hdd not detected)
6B250S0
BANC1980
F/W: R6GBP2
SABRE/RC2

Receiver's platters started to spin, after that the head started to move and make the EXACT noise I hear from my not working DiamondMax Plus 9 of some post above.

Having this situation, can I suppose (not be sure, just suppose) the problem of my DiamondMax Plus 9 is just the pcb (since I could only try a not compatible pcb, and the head was clicking, trying to setup, or whatever) and not some internal damage?


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 8th, 2010, 10:20 
Offline

Joined: October 21st, 2007, 8:48
Posts: 1631
try to be sure about your donor pcb before trying it on the patient drive.


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 13th, 2010, 13:13 
Offline

Joined: January 31st, 2010, 14:42
Posts: 5
Location: Belgium
Hi guys here I am again

I'm going crazy trying to get more info from my dead hdd...
The bios recognize it as MAXTOR CALYPSO
If I set the drive as master, it starts clicking
When slave, no clicks

I read posts regarding how to check the preamp with a multimeter in diode mode and this is my case:

3/9 GND
4/9 -5 --- 0 ohm
5/9 +5 --- 166 ohm

So I guess I have a dead preamp.
But still I read from the various posts if the preamp is dead, each donor pcb I try to swap will be burned...
But my donor pcb still works

Should I definitively give up?


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 14th, 2010, 2:16 
Offline

Joined: June 27th, 2006, 11:33
Posts: 2287
Location: In ur HDD !
Go to a pro.


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 14th, 2010, 4:12 
Offline

Joined: October 21st, 2007, 8:48
Posts: 1631
You should give up DIY, and seek for a pro as Mr.Rameez said.


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 14th, 2010, 4:12 
Offline
User avatar

Joined: September 2nd, 2008, 12:14
Posts: 445
Location: Austria / Europe
Would suggest you contact

the forum member: dobrevjetser

He is from your country and a highly recommended pro.

+++


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: February 14th, 2010, 6:37 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7843
Location: UK
Yes, agree.

Contact dobrevjetser

_________________
PC Image Data Recovery
http://www.pcimage.co.uk

New!! HDD-PCB.COM for all your PCB and donor HDD requirements!


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: July 27th, 2015, 10:30 
Offline

Joined: June 10th, 2011, 8:31
Posts: 6
Location: indonesia
thanks :)


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: May 25th, 2020, 8:39 
Offline

Joined: May 25th, 2020, 8:28
Posts: 1
Location: newyor
Hello,
I know this topic is rather somewhat too old
However I couldnt start a new topic
I have a Maxtor DiamondMax 16 80GB ATA/133 HDD
Code RAMB1TU0
SN:R2124TRE
4R080J0220211

I attached the power cable while the PC was powered on
and I beilive that the pcb is fired and I need to replace it please help me what numbers are the most important for a replacement

thx


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: May 25th, 2020, 11:03 
Offline

Joined: September 29th, 2005, 4:10
Posts: 402
Location: Moscow
woshka,
----
Dear Mr. Robert,...

here is the paragraph that deals with your model type (DiamondMax Plus 9):

For the following Maxtor hard drive models: Fireball 3, DiamondMax 16, DiamondMax Plus 8, DiamondMax Plus 9, Diamond Max 10 and all MaxLine products there is also a GTLA Number on the model (next to barcode on the bottom of the drive). Format 1Y222J2223322. 1, 2 and 3 stand for numbers, Y and J for letters.
The numbers 1 and 3 as well as the letter Y need to be identical to be able to replace the PCB on these drives.

This number can be found on the large sticker on the top of the drive.

Unfortunately we can not give you any more information than this. Any of your DiamondMax Plus 9 drives could possibly have a matching PCB, however it is most likely to be an older one as the drive in question is almost 3 years old.

Kind regards,

Gisela Schubert
Technical Support
Maxtor Ireland Ltd.
-----


Top
 Profile  
 
 Post subject: Re: HowTO How To replace Maxtor Calypso III board
PostPosted: April 29th, 2023, 14:37 
Offline

Joined: April 29th, 2023, 14:34
Posts: 1
Location: Texas
Thanks for this post. I have really had trouble with this thing


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 97 posts ]  Go to page Previous  1, 2, 3, 4, 5

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group