hellooooo (echoooo) is anybondy in heeeerrrrrrrreeeeeee (echoooooo)
| HDD GURU FORUMS http://forum.hddguru.com/ |
|
| TOSHIBA MK6034GSX COD reported as bad PCB? http://forum.hddguru.com/viewtopic.php?f=19&t=14057 |
Page 1 of 1 |
| Author: | mediaman [ November 24th, 2009, 23:48 ] |
| Post subject: | TOSHIBA MK6034GSX COD reported as bad PCB? |
The disk has classic HSA symptoms but Atola 1.4 reports circuit board. Any ideas? Automatic Checkup Finished Report date and time: 11/24/2009 at 7:30 PM Device information: TOSHIBA MK6034GSX Serial number: X6F7T0AUT Firmware revision: AH102E Capacity: 117,210,240 sectors or 60,011,642,880 bytes 512 bytes per sector Diagnostics results According to the status register, circuit board is malfunctioning. Full Diagnostic Log Circuit Board (PCB) Device is powered on. A power cycle is needed... Applying power and watching spin-up currents... Current oscillogram (12V): Current oscillogram (5V): Device is still not ready Registers: 0101 0001 0001 0000 0000 0000 1010 Alt: 1010 According to the status register, circuit board is malfunctioning. Heads Head stack cannot be diagnosed. |
|
| Author: | mediaman [ November 27th, 2009, 19:01 ] |
| Post subject: | Re: TOSHIBA MK6034GSX COD reported as bad PCB? |
hellooooo (echoooo) is anybondy in heeeerrrrrrrreeeeeee (echoooooo)
|
|
| Author: | Dmitry Postrigan [ November 30th, 2009, 19:19 ] |
| Post subject: | Re: TOSHIBA MK6034GSX COD reported as bad PCB? |
Hello Simon, Sorry - I was traveling and unable to check the forum. If you need a fast reply, please use the Atola support forum (it is monitored by everyone at Atola Technology. You can access it by launching the Insight, and then navigating to Help->Support forum. Now to your issue: can you please post the full log including the currents graph? You can export your log into .pdf or .rtf and then attach it here in the topic. Thanks |
|
| Author: | mediaman [ November 30th, 2009, 21:01 ] | ||
| Post subject: | Re: TOSHIBA MK6034GSX COD reported as bad PCB? | ||
Here you go! Thanks Dmitry!
|
|||
| Author: | Dmitry Postrigan [ December 1st, 2009, 0:03 ] |
| Post subject: | Re: TOSHIBA MK6034GSX COD reported as bad PCB? |
Simon, Thanks for the file! It could be either heads or pcb. At this point I would swap the ROM onto a good pcb and then re-ran the diagnostics. |
|
| Author: | mediaman [ December 1st, 2009, 9:27 ] | ||
| Post subject: | Re: TOSHIBA MK6034GSX COD reported as bad PCB? | ||
(furiously looking for donor) thanks Dmitry, will try and feedback results. What does that register value mean?
|
|||
| Author: | Dmitry Postrigan [ December 3rd, 2009, 2:47 ] |
| Post subject: | Re: TOSHIBA MK6034GSX COD reported as bad PCB? |
Simon, From the registers I can say there's potentially an issue with the interface part of the pcb. From the current graph I can say there's head damage. The only way to clarify is to rule out the pcb first. You will need a donor anyway, be it heads or pcb 
|
|
| Author: | mediaman [ December 17th, 2009, 10:29 ] |
| Post subject: | Re: TOSHIBA MK6034GSX COD reported as bad PCB? |
to follow up: it was heads in the end. |
|
| Author: | Russwinters [ December 17th, 2009, 20:20 ] |
| Post subject: | Re: TOSHIBA MK6034GSX COD reported as bad PCB? |
Good news! PCB with those Toshiba drives is not something to look forward working with...big headache unless you have a lot of $$ for the right equipment. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|
