MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Rusolut support forum

All times are UTC - 5 hours [ DST ]

Switch to mobile style


Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 
  Print view Previous topic | Next topic 
Author Message
Sasha Sheremetov
 Post subject: Pinouts of monolithic flash devices
PostPosted: December 4th, 2014, 10:45 
Offline

Joined: July 2nd, 2014, 8:05
Posts: 215
Every update we add pinouts of monolithiс flash devices into built-in database of Visual Nand Reconstructor. You can find them in Trusted Devices database. Just filter list by device type and check images of devices to find the one that looks same as yours.

Image

Image

_________________
VISUAL NAND RECONSTRUCTOR. Since 2014.
Top
 Profile  
 
pcimage
 Post subject: Re: Pinouts of monolithic flash devices
PostPosted: December 4th, 2014, 14:08 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7865
Location: UK
Now, that is neat :-)

_________________
PC Image Data Recovery
http://www.pcimage.co.uk

New!! HDD-PCB.COM for all your PCB and donor HDD requirements!
Top
 Profile  
 
lcoughey
 Post subject: Re: Pinouts of monolithic flash devices
PostPosted: December 4th, 2014, 14:40 
Offline
User avatar

Joined: February 9th, 2009, 16:13
Posts: 2592
Location: Ontario, Canada
pcimage wrote:
Now, that is neat :-)

Would you expect anything less from Sasha?

_________________
Luke
Recovery Force Donor Inventory: 5,000+ Fully Cataloged HDDs & Growing
Top
 Profile  
 
digisupport
 Post subject: Re: Pinouts of monolithic flash devices
PostPosted: December 4th, 2014, 15:04 
Offline
User avatar

Joined: March 6th, 2010, 3:46
Posts: 627
Location: Kolding | Denmark
Nice Sasha :)

_________________
Digitalsupport Data Recovery
https://digitalsupport.dk
Top
 Profile  
 
Sasha Sheremetov
 Post subject: Re: Pinouts of monolithic flash devices
PostPosted: December 5th, 2014, 12:18 
Offline

Joined: July 2nd, 2014, 8:05
Posts: 215
There's a special adapter in Visual Nand Reconstructor kit, that used for monolithic chip soldering (using thin copper wires).
The device must be glued (glue/luquid nails/double sided sticky tape) at the middle of adapter. All signal markings on pinout and adapter are same, so it's easy to solder it properly and not to mix it up.
We use one of the best possible PCB materials, however sometimes golden pads may get damaged (due to overheating). You can solder chip directly to the needles of connector (check picture).
In nearest time we'll make a lot of spare monolith adapters with affordable price (sold separately), so you can use it as expendable material, no need to remove device every time(it's pretty jewelery job that everyone wants to keep :)).

Image

_________________
VISUAL NAND RECONSTRUCTOR. Since 2014.
Top
 Profile  
 
labtech
 Post subject: Re: Pinouts of monolithic flash devices
PostPosted: December 5th, 2014, 12:21 
Offline

Joined: August 18th, 2010, 17:35
Posts: 3669
Location: Massachusetts, USA
I like - on my Santa wish list...

_________________
Hard Disk Drive (HDD), Solid State Drive (SSD, SATA, NVMe, etc), USB Flash Drive and RAID Data Recovery Specialist in Massachusetts
Top
 Profile  
 
HaQue
 Post subject: Re: Pinouts of monolithic flash devices
PostPosted: December 5th, 2014, 18:17 
Offline
User avatar

Joined: December 4th, 2012, 1:35
Posts: 3963
Location: Adelaide, Australia
nice adapters, yes once I have soldered on I don't like removing monolith ;-)
Top
 Profile  
 
positivebit
 Post subject: Re: Pinouts of monolithic flash devices
PostPosted: December 16th, 2014, 5:07 
Offline

Joined: March 28th, 2011, 17:45
Posts: 441
Location: italy
nice tool in the last week i recovered 2 difficoult cases, one with only one nand OK (other nand coudn't even ID) and the adapters are really well built!
Top
 Profile  
 
Arch Stanton
 Post subject: Re: Pinouts of monolithic flash devices
PostPosted: December 8th, 2020, 16:58 
Offline
User avatar

Joined: May 13th, 2019, 7:50
Posts: 1196
Location: Nederland
Sasha Sheremetov wrote:
There's a special adapter in Visual Nand Reconstructor kit, that used for monolithic chip soldering (using thin copper wires).
The device must be glued (glue/luquid nails/double sided sticky tape) at the middle of adapter. All signal markings on pinout and adapter are same, so it's easy to solder it properly and not to mix it up.
We use one of the best possible PCB materials, however sometimes golden pads may get damaged (due to overheating). You can solder chip directly to the needles of connector (check picture).
In nearest time we'll make a lot of spare monolith adapters with affordable price (sold separately), so you can use it as expendable material, no need to remove device every time(it's pretty jewelery job that everyone wants to keep :)).

Image


Can you buy this board separately?

_________________
Joep - http://www.disktuna.com - video & photo repair & recovery service
Top
 Profile  
 
Sasha Sheremetov
 Post subject: Re: Pinouts of monolithic flash devices
PostPosted: December 10th, 2020, 11:55 
Offline

Joined: July 2nd, 2014, 8:05
Posts: 215
We don't have it as a separate item on the web (for now at least), but if you got yours broken from Starter Kit we should be able to sell it (depends on current stock avail.).
Please drop msg to sales@rusolut.com

_________________
VISUAL NAND RECONSTRUCTOR. Since 2014.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 

Main » Forums home » Rusolut support forum

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 1 guest

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group