All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 11 posts ] 
Author Message
 Post subject: Zone allocation table : ........................: Err
PostPosted: December 26th, 2018, 8:33 
Offline

Joined: December 25th, 2018, 3:15
Posts: 11
Location: Varanasi
WD3200BEVT-75A23T0
in MRT Show Error
Zone allocation table : ........................: Err

Any Solutions


Attachments:
wd 320.png
wd 320.png [ 82.18 KiB | Viewed 25215 times ]
Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: December 26th, 2018, 10:43 
Offline

Joined: October 21st, 2007, 8:48
Posts: 1631
What's the drive behavior? (Clicking)?
ATA registers shows nothing? Is the drive spin down?
If yes, then most likely a head/s problem.


Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: December 26th, 2018, 11:08 
Offline

Joined: December 25th, 2018, 3:15
Posts: 11
Location: Varanasi
hard drive sping ok
head test ok
no clinking sound


Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: January 7th, 2019, 2:40 
Offline
User avatar

Banned User

Joined: December 4th, 2018, 3:58
Posts: 10
Location: Russia
Module test ok ? Your information is not enough to make further diagnosis


Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: May 19th, 2019, 19:46 
Offline

Joined: April 30th, 2019, 14:03
Posts: 3
Location: Brasil
I found this solution in another forum. I will try this tomorrow in a hard disk with same problem....

http://www.hddoracle.com/viewtopic.php? ... +rom#p8198


Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: July 22nd, 2021, 17:46 
Offline

Joined: July 21st, 2020, 23:30
Posts: 5
Location: Porto Alegre
Spildit wrote:
Block SA access at start up by shorting points on PCB. Load overlay, load DIR to RAM (initialize dir). Try to check modules.

Similar procedure with WDMarvel (you need to adapt it to MRT) :

http://www.hddoracle.com/viewtopic.php?f=193&t=2339

If it doesn't work :

http://www.hddoracle.com/viewtopic.php?f=193&t=2343

If you get servo errors, etc you might have bad head(s) and/or pre-amp.

Please "adapt" my guides to your MRT tool as i've written my guides to WdMarvel / HRT.


Hi, these links are broken, do you have saved examples?


Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: July 22nd, 2021, 18:24 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15440
Location: Australia
You can download the whole web site (3GB) here:

https://drive.google.com/drive/folders/1CD8h7q9cYNVCltqB87-kSBzMRnq3-yU6?usp=sharing

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: July 22nd, 2021, 20:28 
Offline

Joined: July 21st, 2020, 23:30
Posts: 5
Location: Porto Alegre
fzabkar wrote:



Thank you so much :D


Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: July 22nd, 2021, 20:37 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 15440
Location: Australia
Ricardo Arnoud wrote:
fzabkar wrote:



Thank you so much :D

Thanks should go to @maximus.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: July 23rd, 2021, 4:22 
Offline

Joined: December 5th, 2011, 5:38
Posts: 1625
Location: Italy
I knew that hddoracle would went down since Spildit left the scene.
I'm sad, it was a very good site and Spildit was a cleaver user :( ...i will download the backup too.
Thank you @Spildit, @fzabkar and @maximus.

_________________
My firmware database:
https://mega.nz/folder/O01DkBRI#MxP2J6ZNqXDcrX40I8MoQQ


Top
 Profile  
 
 Post subject: Re: Zone allocation table : ........................: Err
PostPosted: August 18th, 2021, 15:36 
Offline

Joined: July 10th, 2020, 7:34
Posts: 51
Location: India
fzabkar wrote:


Thank you.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group