| HDD GURU FORUMS http://forum.hddguru.com/ |
|
| MRT Software Update Advance Announcement 2021.09 http://forum.hddguru.com/viewtopic.php?f=28&t=41721 |
Page 1 of 4 |
| Author: | vx1 [ September 21st, 2021, 12:35 ] |
| Post subject: | MRT Software Update Advance Announcement 2021.09 |
http://us.mrtlab.com/notice/316.html WD "...firmware unlocking with the locked PCB without the need of unlocked PCB" |
|
| Author: | Abdul Rauf [ September 25th, 2021, 16:08 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
will be very good update if true |
|
| Author: | vx1 [ October 23rd, 2021, 9:05 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
Yes, it really looks like a very good update. Let's wait for the English version. http://info.mrtlab.com/download/ MRT data recovery software update log October 23, 2021 MRT main program, upgrade to 2.1.7.1: 1. Add a shortcut to create a designated port 2. Optimize some underlying functions Programmer module, upgrade to 1.0.7.1: 1. Add support for MRT programmer VER 3.0 2. Optimize the SPI read and write function to make it more stable Western Digital module, upgrade to 2.3.7.1: 1. Added new families: Carmel(800077), VeniceR(810011), SPYG2ULT(810035) 2. Added the function of generating unlocked firmware lock ROM, currently supports mainstream hard disks such as 800065 (Chager), 800066 (Palmer), 800077 (Carmel), 810011 (VeniceR), etc., and supports reading the original ROM directly from the programmer to generate unlocked ROM, Automatic process of writing unlock ROM 3. Add T2 (190) editor (including functions such as obtaining T2, parsing T2, editing T2, etc.) 4. Add T2-based head bitmap creation function for Carmel, VeniceR, Chager and other families 5. Added the function of repairing T2 and writing T2 to the hard disk memory function, which makes the bottom layer all zero failures, read LBA automatic power-off failures, and start-up failures caused by 190 have a better solution 6. Added the firmware lock handshake function, you need to use the serial port to cooperate with the ROM that has released the firmware lock 7. Added the function of manually filling in the module ID and then reading and writing the module 8. Optimized the function of clearing the hard disk password in 127, D006 9. Optimized the ROM writing function and added support for the new hard disk large-capacity ROM chip 10. Optimized the family selection function, and added a dedicated page for the 80xx series family 11. Optimized the function of editing hard disk ID in RAM 12. Optimized the underlying database structure 13. Optimize the scanning function, increase the parameter display 14. Optimized the family recognition function, and there will be no more JET database engine errors 15. Optimized the function of batch saving module 16. The main toolbar adds a serial port connection/disconnection tool button 17. Add log/terminal switch button, serial port switch button, power off/on button on the family selection panel 18. Add full ROM read and write to the ROM list Seagate F3 module, upgrade to 2.0.7.0: 1. Added MCMT analysis function 2. Added MCMT editing function 3. Added MCMT Extent editing function 4. Added the unlocking function of the 97 family firmware lock 5. Added 58 families plus P list, added ST3000DM001-1ER166, ST2000DM001-1ER164, ST1000DM001-1ER162, ST500DM002-1ER14C, ST1000DM001-1CH162, ST2000DM001-1CH164 6. Added HDD ID RAM option 7. Added virtual startup file drag and drop function 8. Added Copy0 and Copy1 options for full backup of system files 9. Added custom baud rate memory attributes (SGT-F3Default.ini) 10. Added backup system files and added a new filtering mechanism (SGT-F3SystemFile.ini) 11. Added a new system file INI file skip mechanism, with the application file skip mechanism to make the reading file system more powerful 12. Optimized the system file description display of 5400.6 13. Optimized the default check of 5400.6 resource full backup 14. Optimized the button display of the handshake mode switch on the main interface 15. Optimized the ID editing function in RAM, and added an uninitialized prompt 16. Optimized the ID editing function of some hard disk service areas to solve the problem of capacity confusion 17. Optimized the possibility of backing up volumes other than volume 0 and 3 during full backup of system files 18. Optimized the underlying database structure 19. Optimized the Glist entry opening function 20. Optimize all F3 configurations, and classify configuration files into the folder Configure 21. Optimized CAP modification capacity (greater than 2T) DE module, upgrade to 6.0.0.4: 1. Added the following stream scan format: Media: FLV, MP4, MP3, AVI, WAV, MKV, RM, AIFF, MIDI Document category: PPTX, XLSX 2. Improve the speed of valid data in marked partitions 3. Optimize the underlying architecture and improve the user experience 4. Added user operation verification to reduce logic errors 5. Improve the speed of file index creation and access 6. Add internal debugging function to assist in locating problems 7. Fix the size of the saved file Phison PS module, upgrade to 1.0.7.0: 1. Added AS2258 write LDR function 2. Added support for AS2258 virtual compiler 3. Optimized the underlying architecture of the PS module 4. Add analysis of new chip Type and other types 5. Optimized the function of reading and writing firmware 6. Optimized reading and writing CP function |
|
| Author: | gps31 [ November 2nd, 2021, 2:16 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
EN version 2.1.7.1 released today http://us.mrtlab.com/download/ |
|
| Author: | unknown [ November 2nd, 2021, 10:59 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
ROM unlocking tested ( Palmer ) OK. Very nice work MRT Lab. |
|
| Author: | HddDonorMarket [ November 18th, 2021, 18:55 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
I have updated to 2.1.7.1 Watched videos and readed PDF unlocking steps. Saying need programmer ver 3. And It would release later. PDF Saying " MRT will release programmer 3 later. "But there is no info about work with old type programmer or terminal. We should desolder Rom , unlock and write unlocked ROM and solder to PCB. After then exchange command. I have bought unlocked PCB's before also. Swap ROM chip to unlocked PCB . thats it. Drive ready directly. Sure MRT's unlocking 800xx PCBs so nice work. But cannot test it yet. |
|
| Author: | lcoughey [ November 18th, 2021, 20:59 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
They also say that it is only supported for sata boards, not USB. |
|
| Author: | ccc [ November 19th, 2021, 3:05 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
I have tested a little more and this is what I've found: You can use one SATA pcb with several ROMs , means, if you have one pcb you can use it several times no matter what ROM you write on it, as long as you use the MRT unlock method. Also it works for Palmer USB pcb if it is connected to terminal. I think it goes the same way for Charger too. Rgds |
|
| Author: | HddDonorMarket [ November 19th, 2021, 19:23 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
lcoughey wrote: They also say that it is only supported for sata boards, not USB. Working on palmer For USB>> Read Rom dump, Unlock with MRT and write directly to Rom chip or an unlocked PCB with MRT. Tested Palmer USB and SATA working good. pcb 800069. 800066 |
|
| Author: | Amarbir[CDR-Labs] [ November 20th, 2021, 6:00 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
Well, I have been saying this since ages ,MRT is a Great Data Recovery Tool but the only issue is its Data Extractor And Support/Documentation . |
|
| Author: | gps31 [ November 21st, 2021, 10:30 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
HddDonorMarket wrote: lcoughey wrote: They also say that it is only supported for sata boards, not USB. Working on palmer For USB>> Read Rom dump, Unlock with MRT and write directly to Rom chip or an unlocked PCB with MRT. Tested Palmer USB and SATA working good. pcb 800069. 800066 can you post how to connect terminal to 2060-800069-001 (TX and RX) Pls |
|
| Author: | HddDonorMarket [ November 22nd, 2021, 3:47 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
gps31 wrote: HddDonorMarket wrote: lcoughey wrote: They also say that it is only supported for sata boards, not USB. Working on palmer For USB>> Read Rom dump, Unlock with MRT and write directly to Rom chip or an unlocked PCB with MRT. Tested Palmer USB and SATA working good. pcb 800069. 800066 can you post how to connect terminal to 2060-800069-001 (TX and RX) Pls Desoldering ROM chip and external reader |
|
| Author: | lcoughey [ November 22nd, 2021, 10:24 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
HddDonorMarket wrote: lcoughey wrote: They also say that it is only supported for sata boards, not USB. Working on palmer For USB>> Read Rom dump, Unlock with MRT and write directly to Rom chip or an unlocked PCB with MRT. Tested Palmer USB and SATA working good. pcb 800069. 800066 I figured that process should work, but then you still have to have a terminal connection to handle the handshake command, I presume. |
|
| Author: | HddDonorMarket [ November 22nd, 2021, 15:34 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
lcoughey wrote: HddDonorMarket wrote: lcoughey wrote: They also say that it is only supported for sata boards, not USB. Working on palmer For USB>> Read Rom dump, Unlock with MRT and write directly to Rom chip or an unlocked PCB with MRT. Tested Palmer USB and SATA working good. pcb 800069. 800066 I figured that process should work, but then you still have to have a terminal connection to handle the handshake command, I presume. Its true. Steps for USB or SATA locked PCB (according to my equipment. Sata PCB+ Terminal,+ external programmer (MRT set have it.) -Desolder ROM from USB PCB -Put USB ROM chip to external programmer (opt. backup original locked ROM dump=A) -Connect WD utility, -"Unlock and write" to ROM over external programmer (or sellect locked ROM file (A) ,make unlocked Rom file (B) and write unlockled file to chip (C) with external programmer manually) -Solder unlocked Rom to SATA PCB (C) (Or write unlocked ROM (B) to sata PCB over WD utilty. You should have an unlocked PCB. so it should allow to write rom ) -And SATA PCB ready . -Connect WD utility +terminal + handshake (exchange command) -Access SA |
|
| Author: | EnigmaSpace [ January 14th, 2022, 10:25 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
Attachment: 2022-01-14_19-50-11.png [ 5.4 KiB | Viewed 45524 times ] I am Having this error , Any Solution ? Does MRT Strictly Requires Programmer 3.0 . I have Programmer 2.0 . Please Help . Attachment: 2022-01-14_19-54-29.png [ 28.86 KiB | Viewed 45524 times ] |
|
| Author: | ccc [ January 15th, 2022, 4:55 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
Did you connected the ver 2.0 programmer to the MRT board? |
|
| Author: | DR-Kiev [ January 17th, 2022, 12:54 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
Programmer has no much matter since you can desolder ROM read it using different pcb or cheap programmer, patch it as ROM file in MRT , write and solder back. |
|
| Author: | ccc [ January 18th, 2022, 2:32 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
DR-Kiev wrote: Programmer has no much matter since you can desolder ROM read it using different pcb or cheap programmer, patch it as ROM file in MRT , write and solder back. That is the problem.......In the last version of the software, when you try to patch from file, not from programmer, it still asks for programmer to be present. I have talked with them and they say it's a "strategy ". They prohibit use of other hardware with MRT software..... In other words, if we want to patch from file we will need the ver 3.0 programmer. Shame on them. It's not fair. |
|
| Author: | EnigmaSpace [ January 18th, 2022, 2:44 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
ccc wrote: DR-Kiev wrote: Programmer has no much matter since you can desolder ROM read it using different pcb or cheap programmer, patch it as ROM file in MRT , write and solder back. That is the problem.......In the last version of the software, when you try to patch from file, not from programmer, it still asks for programmer to be present. I have talked with them and they say it's a "strategy ". They prohibit use of other hardware with MRT software..... In other words, if we want to patch from file we will need the ver 3.0 programmer. Shame on them. It's not fair. But Some are saying that it is working on there PCs with old Programmer without any errors. ruivo2 wrote: MRT Unlock Rom Palmer pcb 800066 Very nice work MRT Lab! Follow link; https://www.youtube.com/watch?v=ncxHp4BvWKM HERE , In Above video it doesn't ask for any Programmer. |
|
| Author: | ccc [ January 18th, 2022, 3:03 ] |
| Post subject: | Re: MRT Software Update Advance Announcement 2021.09 |
It was the first 2171 version of software that was working without asking for programmer. |
|
| Page 1 of 4 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|