| HDD GURU FORUMS http://forum.hddguru.com/ |
|
| Cloning Firmware http://forum.hddguru.com/viewtopic.php?f=7&t=10087 |
Page 1 of 1 |
| Author: | borgfish [ October 8th, 2008, 4:23 ] |
| Post subject: | Cloning Firmware |
Hello People, since you are the hdd gurus  i have a question: I want to grab the firmware off a branded oem drive and put it on new retail drives. Are there suggestions what i will be needing for this ? Is software sufficient or do i need extra Hardware for this task. p.s. i strongly believe this firmware is not available anywhere so no chance for a download.
|
|
| Author: | shahij [ October 8th, 2008, 4:28 ] |
| Post subject: | Re: Cloning Firmware |
u must need special HW. and offcourse, ur downloaded fw could not be used to next drives untill it mathces. its not like MOBILE FLASH. just keep it mind. |
|
| Author: | borgfish [ October 8th, 2008, 4:30 ] |
| Post subject: | Re: Cloning Firmware |
you mean i need the exactly same harddisk ? sure i know. now how much would this hardware be ? i guess you mean the pc3000 pci card ? not that i buy one from chinese , how much would the real thing be for me ? are there distributors in germany ? |
|
| Author: | shahij [ October 8th, 2008, 4:34 ] |
| Post subject: | Re: Cloning Firmware |
if u r going to do for a single HDD, no profit at all. and also, its not possible to do the job having learnt in a magic time. need contiuous struggle, and offcourse without sleeping a lot of night. |
|
| Author: | borgfish [ October 8th, 2008, 4:41 ] |
| Post subject: | Re: Cloning Firmware |
thanks for your time shahij, but if i can buy 15 drives for 200$ each instead of 600$ i guess there is pretty room for saving money, except the pc3000 costs 6000$. and i hope handling of the software for dumping and restoring a firmware is not so difficult at all ? is there a website from the manufacturers of the real thing so i can check if the drive is supported and if there are resellers here ? |
|
| Author: | shahij [ October 8th, 2008, 4:49 ] |
| Post subject: | Re: Cloning Firmware |
your money, your headache. all up to you. best of luck |
|
| Author: | borgfish [ October 8th, 2008, 5:46 ] |
| Post subject: | Re: Cloning Firmware |
my companys money, my fun! sorry to have to say that, but you are not very helpful |
|
| Author: | dobrevjetser [ October 8th, 2008, 9:11 ] |
| Post subject: | Re: Cloning Firmware |
What drive is it ? If it is a very recent drive, then there is no support yet. Tell me the type and I'll tell you if its supported and by what. Best regards, Dobre |
|
| Author: | borgfish [ October 8th, 2008, 9:22 ] |
| Post subject: | Re: Cloning Firmware |
its a seagate barracuda ES: ST3750640NS |
|
| Author: | dobrevjetser [ October 8th, 2008, 9:32 ] |
| Post subject: | Re: Cloning Firmware |
The only tool that supports that drive is the Salvation data disk doctor for Seagate. You could also work on it with the pc3K UDMA version, but there you would be limited to working with the terminal, what i cannot advice for a novice. So my best advice it to contact salvation data. Best regards, Dobre |
|
| Author: | borgfish [ October 8th, 2008, 9:45 ] |
| Post subject: | Re: Cloning Firmware |
thanks for that answer, i already mailed them about their old product SalvationDATA HDD Repairer (Seagate) PRO hopefully i have an answer tomorrow |
|
| Author: | shahij [ October 8th, 2008, 12:25 ] |
| Post subject: | Re: Cloning Firmware |
borgfish wrote: my companys money, my fun! sorry to have to say that, but you are not very helpful I adviced you, nothing else. But you take it as negative sense. Anyway, order for the HD DOCTOR FOR SEAGATE, Not the old... |
|
| Author: | mediaman [ October 8th, 2008, 13:03 ] |
| Post subject: | Re: Cloning Firmware |
check atolas website to see if it is supported. if it is you can dump FW and re=write with that. Have a feeling its not supported though |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|