Page 1 of 2
The death of WD ROM recovery tool: U instruction
Posted: December 6th, 2012, 3:49
by nafangkuaixiu
Function: through instruction restores normal brush to write ROM program; the scope of application: ROM program embedded in the main control chip MCU series of hard disk ( eight feet ROM chip drive circuit board ); principle: short circuit drive circuit board CPU specific foot position, Using special software, via the serial port, reflash the internal or external ROM( not data line hard circuit board ) to the CPU sends an activation command and ROM data, enable the CPU ROM program resumed control of hard work.
Method of use: to install: NET4.0,13XX series circuit board in circuit board E112 plus 3.3V voltage, connected with the serial port communication line, then drive power supply ( not connected with the data line ): run U commands, COM export, call, the following SSS is connected, the selected file, writing brush, so simple.
Re: The death of WD ROM recovery tool: U instruction
Posted: December 16th, 2012, 14:44
by justin_123
thanks alot
but i want explaining about how to connect pcb with serial port ?
Re: The death of WD ROM recovery tool: U instruction
Posted: December 17th, 2012, 1:17
by nafangkuaixiu
justin_123 wrote:thanks alot
but i want explaining about how to connect pcb with serial port ?
QQ370909447
Re: The death of WD ROM recovery tool: U instruction
Posted: December 21st, 2012, 10:37
by Friedrich
I don't understand what does this tool?
Western digital can be hooked to a serial port as Seagate hdd?
Re: The death of WD ROM recovery tool: U instruction
Posted: December 21st, 2012, 11:34
by Doomer
Here is what he's saying
1. Take WD PCB(ARM based) that has erased or incompatible ROM image (bricked PCB)
2. Connect serial port as shown
3. Short some magic pins to start X-Modem sequence in MCU boot code(E112 and 3.3V for PCB 13xx, 1335 for example). The number is etched on PCB as 2060-701335-xxx
4. Select correct ROM image file and flash it to the drive with the program. Program will use special loaders (called EraseL.dll, SystemL.dll) to do so
5. Per my understanding, provided utility supports only 128KB flash files (external flash chips). For 192KB flash the program will look for Erase.dll and System.dll files that are not provided, thus will not work with those.
Re: The death of WD ROM recovery tool: U instruction
Posted: December 21st, 2012, 12:41
by Friedrich
Can this work also with pcb 2060-701477-002 ?
Also, in point 4 you say "Select correct ROM image file and flash it to the drive with the program". Where do i get the correct ROM file if my is erased?
Re: The death of WD ROM recovery tool: U instruction
Posted: December 21st, 2012, 13:27
by einstein9
Doomer wrote:Here is what he's saying
1. Take WD PCB(ARM based) that has erased or incompatible ROM image (bricked PCB)
2. Connect serial port as shown
3. Short some magic pins to start X-Modem sequence in MCU boot code(E112 and 3.3V for PCB 13xx, 1335 for example). The number is etched on PCB as 2060-701335-xxx
4. Select correct ROM image file and flash it to the drive with the program. Program will use special loaders (called EraseL.dll, SystemL.dll) to do so
5. Per my understanding, provided utility supports only 128KB flash files (external flash chips). For 192KB flash the program will look for Erase.dll and System.dll files that are not provided, thus will not work with those.
Agree with you here
and wanted to add: There are many ROUTES to the SAME destination
and 4 sure, this is one of them.
but @ the end of this, something good came up here
Re: The death of WD ROM recovery tool: U instruction
Posted: December 22nd, 2012, 11:07
by nafangkuaixiu
einstein9 wrote:Doomer wrote:Here is what he's saying
1. Take WD PCB(ARM based) that has erased or incompatible ROM image (bricked PCB)
2. Connect serial port as shown
3. Short some magic pins to start X-Modem sequence in MCU boot code(E112 and 3.3V for PCB 13xx, 1335 for example). The number is etched on PCB as 2060-701335-xxx
4. Select correct ROM image file and flash it to the drive with the program. Program will use special loaders (called EraseL.dll, SystemL.dll) to do so
5. Per my understanding, provided utility supports only 128KB flash files (external flash chips). For 192KB flash the program will look for Erase.dll and System.dll files that are not provided, thus will not work with those.
Agree with you here
and wanted to add: There are many ROUTES to the SAME destination
and 4 sure, this is one of them.
but @ the end of this, something good came up here
Re: The death of WD ROM recovery tool: U instruction
Posted: December 22nd, 2012, 11:10
by nafangkuaixiu
Doomer wrote:Here is what he's saying
1. Take WD PCB(ARM based) that has erased or incompatible ROM image (bricked PCB)
2. Connect serial port as shown
3. Short some magic pins to start X-Modem sequence in MCU boot code(E112 and 3.3V for PCB 13xx, 1335 for example). The number is etched on PCB as 2060-701335-xxx
4. Select correct ROM image file and flash it to the drive with the program. Program will use special loaders (called EraseL.dll, SystemL.dll) to do so
5. Per my understanding, provided utility supports only 128KB flash files (external flash chips). For 192KB flash the program will look for Erase.dll and System.dll files that are not provided, thus will not work with those.
Re: The death of WD ROM recovery tool: U instruction
Posted: December 22nd, 2012, 22:01
by thatdellguy
I tried it on a ATLANTIS PATA with erased ROM (thanks to SD tools) and it didnt work.
Re: The death of WD ROM recovery tool: U instruction
Posted: December 23rd, 2012, 2:55
by nafangkuaixiu
thatdellguy wrote:I tried it on a ATLANTIS PATA with erased ROM (thanks to SD tools) and it didnt work.
The trial version only hosted 13XX series motherboards, the registered version supports 13XX, 14XX, 15XX series motherboards. More please contact QQ370909447 technical Street
Re: The death of WD ROM recovery tool: U instruction
Posted: December 23rd, 2012, 20:43
by Kamen
Actually do I need to
Short some magic pins to start X-Modem
for your utility ?
Re: The death of WD ROM recovery tool: U instruction
Posted: December 23rd, 2012, 22:57
by thatdellguy
What is "QQ370909447 technical Street"?
Re: The death of WD ROM recovery tool: U instruction
Posted: December 24th, 2012, 4:01
by northwind
QQ is equivalent to MSN for China, very popular.
Re: The death of WD ROM recovery tool: U instruction
Posted: December 24th, 2012, 4:39
by thatdellguy
Never heard of it but figured it sounded like some ICQ messenger spin off.
Re: The death of WD ROM recovery tool: U instruction
Posted: December 28th, 2012, 15:33
by Tink
Jtag -taxis!
Re: The death of WD ROM recovery tool: U instruction
Posted: January 18th, 2013, 10:38
by ahmedshref
we need aphoto to com plese
Re: The death of WD ROM recovery tool: U instruction
Posted: January 19th, 2013, 1:45
by nafangkuaixiu
ahmedshref wrote:we need aphoto to com plese
Re: The death of WD ROM recovery tool: U instruction
Posted: January 19th, 2013, 1:46
by nafangkuaixiu
ahmedshref wrote:we need aphoto to com plese
Re: The death of WD ROM recovery tool: U instruction
Posted: January 19th, 2013, 2:13
by nafangkuaixiu
ahmedshref wrote:we need aphoto to com plese
http://www.drthdd.com/drte/index.htm