MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 12 posts ] 
  Previous topic | Next topic 
Author Message
marwan
 Post subject: G-lis to P-lis error
PostPosted: November 17th, 2016, 23:36 
Offline
User avatar

Joined: November 7th, 2016, 0:30
Posts: 34
Location: indonesia
HI FRIENDS, IS THERE THAT CAN HELP ME WITH THIS PROBLEM ..
how to improve G-lis to P-lis error ..


Attachments:
ScreenHunter_01 Nov. 18 10.26.jpg
ScreenHunter_01 Nov. 18 10.26.jpg [ 249.34 KiB | Viewed 14549 times ]
Top
 Profile  
 
michael chiklis
 Post subject: Re: G-lis to P-lis error
PostPosted: November 19th, 2016, 10:25 
Offline

Joined: December 5th, 2011, 5:38
Posts: 1741
Location: Verona, Italy
G list to P-list never worked when i tried in MRT Hitachi utility.
MRT has many bugs, this is one of those.

_________________
My firmware database:
https://mega.nz/folder/O01DkBRI
Top
 Profile  
 
Moltke
 Post subject: Re: G-lis to P-lis error
PostPosted: November 19th, 2016, 10:50 
Offline

Joined: October 24th, 2005, 17:04
Posts: 242
wrt0,wrt1.
do not write two heads ?
Top
 Profile  
 
michael chiklis
 Post subject: Re: G-lis to P-lis error
PostPosted: November 21st, 2016, 5:45 
Offline

Joined: December 5th, 2011, 5:38
Posts: 1741
Location: Verona, Italy
Spildit wrote:
Moltke wrote:
wrt0,wrt1.
do not write two heads ?


I think that MRT will not read those modules properly and will state error even on Known GOOD DRIVES ...

:D :D :D


You think right, MRT returns always error when you try to read those mod, even if the drive is new and perfectly working.

_________________
My firmware database:
https://mega.nz/folder/O01DkBRI
Top
 Profile  
 
drHDD
 Post subject: Re: G-lis to P-lis error
PostPosted: November 21st, 2016, 17:18 
Offline

Joined: October 5th, 2015, 18:53
Posts: 488
Location: US
Drive is using (checking writing) only first sector of those modules. So first sector should be readable. If not - there is problem with heads - just writing or reading or both in same time. (Or there is bad sector.)
Top
 Profile  
 
drHDD
 Post subject: Re: G-lis to P-lis error
PostPosted: November 21st, 2016, 17:28 
Offline

Joined: October 5th, 2015, 18:53
Posts: 488
Location: US
read carefully. I am not talking about programs and how they work with modules. If stupid program trying to read module where only first sector formatted - I don't care. You can use my info or not - it's up to you.
Top
 Profile  
 
marwan
 Post subject: Re: G-lis to P-lis error
PostPosted: November 24th, 2016, 2:40 
Offline
User avatar

Joined: November 7th, 2016, 0:30
Posts: 34
Location: indonesia
so what should i do .. do I need to buy another seftware ..?
Top
 Profile  
 
michael chiklis
 Post subject: Re: G-lis to P-lis error
PostPosted: November 24th, 2016, 9:03 
Offline

Joined: December 5th, 2011, 5:38
Posts: 1741
Location: Verona, Italy
I bought few days ago Sediv for Hitachi, but i still haven't tried it yet, as i know it should work properly when working on hitachi fw. Sediv is very good software for fw repair, the only limitation of it is that it doesn't have data extractor for data cloning and is strongly restricted to computer hardware and software configuration, this means that if you change your computer configuration after you have activated sediv (i mean since you get sediv license) then it will stop working on your computer.
The only way to make it work again is by returning to previous pc configuration, or by activating it again.

_________________
My firmware database:
https://mega.nz/folder/O01DkBRI
Top
 Profile  
 
marwan
 Post subject: Re: G-lis to P-lis error
PostPosted: November 25th, 2016, 3:14 
Offline
User avatar

Joined: November 7th, 2016, 0:30
Posts: 34
Location: indonesia
Application WHAT Should I buy,, so that I can be to fix it ..?
Top
 Profile  
 
michael chiklis
 Post subject: Re: G-lis to P-lis error
PostPosted: December 3rd, 2016, 10:23 
Offline

Joined: December 5th, 2011, 5:38
Posts: 1741
Location: Verona, Italy
I have at the moment a new HGST HTS545050A7E680 drive FW: GR20A3J0 which is not supported yet by Sediv (i can't access into SA), but also MRT is not able to access into it by utility.
When i will get another hitachi drive which is supported by sediv, i will do some G to P test

_________________
My firmware database:
https://mega.nz/folder/O01DkBRI
Top
 Profile  
 
datasevices
 Post subject: Re: G-lis to P-lis error
PostPosted: December 4th, 2016, 13:17 
Offline

Banned User

Joined: December 3rd, 2016, 21:00
Posts: 6
Location: Localhosst
You should contact the support team MRT to better
Top
 Profile  
 
waqas_ali766
 Post subject: Re: G-lis to P-lis error
PostPosted: January 15th, 2017, 6:38 
Offline

Joined: July 6th, 2013, 15:13
Posts: 311
Location: ISLAMABAD
Hi Michael

You can move G to P of Hitachi Drive, Even if you not have SA access.

Select option ARM, then press ok to enter into Utility, then goto translator> G to P

thats all.

its works by VSC commands
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 12 posts ] 

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: Google [Bot] and 44 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group