MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 16 posts ] 
  Previous topic | Next topic 
Author Message
pcimage
 Post subject: Help please with Maxtor N40P
PostPosted: April 26th, 2007, 9:44 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7864
Location: UK
Hi all,

A little help?

Maxtor 40Gb 6E040L0..........

Seen in BIOS, but f/w version wrong (ending in Z)...

So, enter Safe Mode.... Load LDR... check modules, all OK.

Run module recovery...

Now drive ID's OK, but all LBA is bad (every single one)

Run translator regen, (97k+ defects), still same.

Any suggestions?

PC3000 manual says to delete G-List, did that (saved copy 1st), still same.

Help!!
Top
 Profile  
 
Starling
 Post subject:
PostPosted: April 26th, 2007, 10:20 
Offline

Joined: January 29th, 2005, 22:58
Posts: 637
Location: Canada
What are the errors in the LBAs?
UNC/AMNF?
Top
 Profile  
 
pcimage
 Post subject:
PostPosted: April 26th, 2007, 11:28 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7864
Location: UK
Thanks for reply Starling...

Error is "HDD Readiness timeout"

Any help?
Top
 Profile  
 
rameez
 Post subject:
PostPosted: April 26th, 2007, 14:47 
Offline

Joined: June 27th, 2006, 11:33
Posts: 2288
Location: In ur HDD !
The hdd must be showing N40P NAr6159Z this is a normal thing the "Z" letter indicates that something wrong with SA do one thing if this is the problem Load only modules in normal mode from loader the Check SA and post results here .
Top
 Profile  
 
pcimage
 Post subject:
PostPosted: April 26th, 2007, 14:50 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7864
Location: UK
Thanks for the reply Remeez,

Drive is showing correct NAR61EA0 now, all modules check out OK.

Just EVERY single sector of user area is "HDD Readiness timeout" :-(
Top
 Profile  
 
beto
 Post subject: pci image
PostPosted: April 26th, 2007, 15:20 
Offline

Joined: October 21st, 2005, 0:45
Posts: 1517
Location: Mexico
Show BSY? can u heard the recalibration sound??


Best Regards

Sinceraly

Alberto
Top
 Profile  
 
rameez
 Post subject:
PostPosted: April 26th, 2007, 16:26 
Offline

Joined: June 27th, 2006, 11:33
Posts: 2288
Location: In ur HDD !
no its not showing BSY all hdd filled with bad sectors .
Do u need data ?
Top
 Profile  
 
pcimage
 Post subject:
PostPosted: April 26th, 2007, 17:23 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7864
Location: UK
Yes, i need data.
Top
 Profile  
 
rameez
 Post subject:
PostPosted: April 26th, 2007, 17:34 
Offline

Joined: June 27th, 2006, 11:33
Posts: 2288
Location: In ur HDD !
did u regenerate translator for this problem ?
Top
 Profile  
 
pcimage
 Post subject:
PostPosted: April 26th, 2007, 18:25 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7864
Location: UK
Yes
Top
 Profile  
 
pcimage
 Post subject:
PostPosted: April 27th, 2007, 8:40 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7864
Location: UK
A bit more light to shed on this case.

Drive will read data now, but very, very slowly. And with quite a few bad sectors near the beginning.

Took one hour to image 4,000 sectors, so the 40Gb will take 2,000 hours :-(

SA reading is normal speed.

Any suggestions?

Sean
Top
 Profile  
 
Starling
 Post subject:
PostPosted: April 27th, 2007, 10:49 
Offline

Joined: January 29th, 2005, 22:58
Posts: 637
Location: Canada
It seems like media is degrading...
Try smart hot swap to read the data.
Top
 Profile  
 
pcimage
 Post subject:
PostPosted: April 27th, 2007, 12:48 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7864
Location: UK
Starling.. Thx for reply my friend...

Forgive me but what is a "smart" hot swap?

You mean to copy the defect tables and translator modules to donor, start then hot swap?
Top
 Profile  
 
Starling
 Post subject:
PostPosted: April 27th, 2007, 13:28 
Offline

Joined: January 29th, 2005, 22:58
Posts: 637
Location: Canada
Yes, exactly.
Top
 Profile  
 
rameez
 Post subject:
PostPosted: April 27th, 2007, 13:47 
Offline

Joined: June 27th, 2006, 11:33
Posts: 2288
Location: In ur HDD !
u mean rewrite the Smart table and defect table from donor hdd ?
Top
 Profile  
 
Shortscurcuits
 Post subject:
PostPosted: April 27th, 2007, 17:51 
Offline

Joined: November 15th, 2005, 11:05
Posts: 189
Location: Canada
write smart & translator modules from HDD you need to recover data from to the HDD you will start the hot swap process with. Start good drive, let it initialize put to sleep with command, then move PCB still connected to recovery drive & try to copy data

_________________
I think ST is a sub company of Lucas
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 16 posts ] 

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: Google [Bot] and 47 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group