MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Switch to mobile style


Post new topic Reply to topic  Page 1 of 1
  [ 7 posts ] 
  Previous topic | Next topic 
Author Message
ceckin
 Post subject: A bit of help with WD2500AAJS
PostPosted: January 27th, 2012, 16:33 
Offline

Joined: May 14th, 2011, 19:39
Posts: 5
Location: Bulgaria
Guys i come accross a strange hdd, its WD that have a lot bad sectors and results in I/O errors. Does anyone have a suggestion how can i skip this sectors and use the good ones instead? I'm perfectly aware that this drive cannot be saved with software i just want to try and use it for insensitive data (as caching) for as long as i can.

This is the SMART report:
Code:
ID   Attribute Description   Threshold   Value   Worst   Data   Status
01   Raw Read Error Rate   51   198   198   37847   OK: Value is normal
03   Spinup Time   21   194   178   1291   OK: Value is normal
04   Start/Stop Count   0   100   100   185   OK: Always passes
05   Reallocated Sector Count   140   104   104   761   Pre-Failure: Imminent loss of data is being predicted
07   Seek Error Rate   0   193   190   305   OK: Always passes
09   Power-On Time Count   0   80   80   14887   OK: Always passes
0A   Spinup Retry Count   0   100   100   0   OK: Always passes
0B   Calibration Retry Count   0   100   100   0   OK: Always passes
0C   Power Cycle Count   0   97   97   3864   OK: Always passes
C0   Power-Off Retract Count   0   197   197   2741   OK: Always passes
C1   Load/Unload Cycle Count   0   199   199   3864   OK: Always passes
C2   Temperature   0   107   87   36   OK: Always passes
C4   Reallocation Event Count   0   1   1   232   OK: Always passes
C5   Current Pending Sector Count   0   200   197   0   OK: Always passes
C6   Offline Uncorrectable Sector Count   0   200   200   40   OK: Always passes
C7   Ultra ATA CRC Error Rate   0   200   200   134   OK: Always passes
C8   Write Error Rate   0   200   200   33   OK: Always passes
Top
 Profile  
 
poehere
 Post subject: Re: A bit of help with WD2500AAJS
PostPosted: January 27th, 2012, 17:21 
Offline
User avatar

Joined: February 27th, 2009, 3:26
Posts: 1721
Location: French Polynesia Tahiti
Try MHDD to do this one with. But as you say you are not going to get so far on this one and it is not such a great idea to use it if this is the problem.

_________________
Iorana Haraharaini
Top
 Profile  
 
BlackST
 Post subject: Re: A bit of help with WD2500AAJS
PostPosted: January 27th, 2012, 18:50 
Offline

Joined: July 18th, 2006, 3:05
Posts: 7476
Location: ITALY
Mhdd won't help that much, you need your drive to be professionally fixed. If successful, it will be like brand new.
Top
 Profile  
 
pcimage
 Post subject: Re: A bit of help with WD2500AAJS
PostPosted: January 27th, 2012, 18:53 
Offline

Joined: November 29th, 2006, 10:08
Posts: 7864
Location: UK
Drive is dying, but could be recertified and reusable. But not without specialist tools I'm afraid :-(

_________________
PC Image Data Recovery
http://www.pcimage.co.uk

New!! HDD-PCB.COM for all your PCB and donor HDD requirements!
Top
 Profile  
 
ceckin
 Post subject: Re: A bit of help with WD2500AAJS
PostPosted: January 27th, 2012, 21:37 
Offline

Joined: May 14th, 2011, 19:39
Posts: 5
Location: Bulgaria
What are these tools? PC3k? Or just high-price software?
Top
 Profile  
 
fzabkar
 Post subject: Re: A bit of help with WD2500AAJS
PostPosted: January 28th, 2012, 18:12 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 16960
Location: Australia
ceckin wrote:
What are these tools? PC3k? Or just high-price software?

AIUI, if the drive needs to be opened, then the job wouldn't be worth doing. Instead I would expect that it would all be done from behind a keyboard. I would think that a bad head or surface would simply be disabled, and the drive recertified at a reduced capacity.

If that's the case, then there are cheap software tools that could probably do the job, eg WD HD Pro (US$80 - $100) or WDR-UDMA (US$150).

_________________
A backup a day keeps DR away.
Top
 Profile  
 
poehere
 Post subject: Re: A bit of help with WD2500AAJS
PostPosted: January 30th, 2012, 13:13 
Offline
User avatar

Joined: February 27th, 2009, 3:26
Posts: 1721
Location: French Polynesia Tahiti
BlackST wrote:
Mhdd won't help that much, you need your drive to be professionally fixed. If successful, it will be like brand new.


This does not mean to open the HDD. Professionally fixed = refurbished. It is done by the SA and special commands to refurbish a HDD. Normally a refurbish process on a HDD is rather cheap. I can not quote you an exact price but I know it normally is under 30 euro on this one I think. Do not take my quote as your final price. Send BlackST a PM and ask him how much it would be to do this for you. He can give you the price on this and I have read on here sometime as low as 10 to 30 euro.

_________________
Iorana Haraharaini
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 7 posts ] 

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: Google [Bot] and 30 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group