MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Switch to mobile style


Post new topic Reply to topic  Page 1 of 2
  [ 23 posts ]  Go to page 1, 2  Next
  Previous topic | Next topic 
Author Message
Jirbun
 Post subject: ST1000LM035 rosewood clicking after replace many new heads
PostPosted: July 30th, 2023, 17:39 
Offline

Joined: February 1st, 2016, 19:51
Posts: 147
Location: Cyprus
Hi

I tried all preamp available types.
Although main rom moduls without CRC errors I analyzed the rom content.
I found one bit which does not appear in any of the dozens of rom I checked.
When I changed the bit to the value that appears in the others(it's the same in everyone in that family),so no more clicking but there are these errors:
Boot 0x80M
TCC:001F
[LBA=0x00000001][LBA=0x00000001]
RECOV Servo Op=06DF Resp=0005
DSC PASS
RECOV Servo Op=0095 Resp=0005
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=0000000000000001 Duration=0000063E ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DA01][LBA=0x0000DA01]
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=000000000000DA01 Duration=00000048 ms
RECOV Servo Op=0095 Resp=0005[LBA=0x00000406][LBA=0x00000406]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=0000000000000406 Duration=00000047 ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DE06][LBA=0x0000DE06]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=000000000000DE06 Duration=00000046 ms
SimError - Remaining in BootFW
Perform a double download without a power cycle.

I checked, these errors are because eight lines within the SAP.
But in these eight lines there are many possibilities.

I will pay for a solution.
Top
 Profile  
 
gps31
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: July 30th, 2023, 23:48 
Offline

Joined: January 18th, 2010, 23:53
Posts: 346
Location: india
Which bit u changed? u may try Virtual boot MRT
Top
 Profile  
 
Jirbun
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: July 31st, 2023, 9:27 
Offline

Joined: February 1st, 2016, 19:51
Posts: 147
Location: Cyprus
MRT virtual output:

TCC:0023
[LBA=0x00000001][LBA=0x00000001]
RECOV Servo Op=06DF Resp=0005
DSC PASS
RECOV Servo Op=0095 Resp=0005
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=0000000000000001 Duration=00000607 ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DA01][LBA=0x0000DA01]
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=000000000000DA01 Duration=00000048 ms
RECOV Servo Op=0095 Resp=0005[LBA=0x00000406][LBA=0x00000406]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=0000000000000406 Duration=00000047 ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DE06][LBA=0x0000DE06]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=000000000000DE06 Duration=00000046 ms
---Mrt Loader---
LockCode:0x9288DA10
LockKey:Recv Loader....Redy

Rst 0x80M
T:0x0001 0x0AF0B48E
LED:0x000000BD FAddr:0x00009039

PrgF
LED:0x000000BD FAddr:0x00009039

LED:0x000000BD FAddr:0x00009039
Top
 Profile  
 
Amarbir[CDR-Labs]
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 14:15 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3522
Location: CDRLabs @ Chandigarh [ India ]
Hi,
I had a similiar case with 4TB hdd ,The issue was the smart a@#@# data recovery technician before me had headmap to 00 00 00 00 04 04 040 04 lol .Disable Media Cache For The Time Being And Try And Also Check Headmap in ROM

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com
Top
 Profile  
 
Jirbun
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 21:46 
Offline

Joined: February 1st, 2016, 19:51
Posts: 147
Location: Cyprus
Amarbir[CDR-Labs] wrote:
Hi,
I had a similiar case with 4TB hdd ,The issue was the smart a@#@# data recovery technician before me had headmap to 00 00 00 00 04 04 040 04 lol .Disable Media Cache For The Time Being And Try And Also Check Headmap in ROM

Head map are correct.
Drive ID with capacity -1 (8796093022208.00 GB) in this state it is not possible to perform any action so I can't disable Media Cache.
I changed one bit at offset 802F6(SAP 2F6) from 89 to 09 and it stop click but can't ID.
Besides I found that 99% of sap you can take from donor and somehow to get access to the drive only 1% need to be original in this case I have a problem with that 1%.

Thanks
Top
 Profile  
 
Doomer
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 21:55 
Offline
User avatar

Joined: September 29th, 2005, 12:02
Posts: 3577
Location: Chicago
you drive has rare heads, check if the heads vendor is marked "alternative" instead of "default" in pc3k rom dialog.
very likely your drive is "alternative" and all the donors are "default".

you'd need correct heads vendor for the donor

_________________
SAN, NAS, RAID, Server, and HDD Data Recovery.
Top
 Profile  
 
Jirbun
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 22:42 
Offline

Joined: February 1st, 2016, 19:51
Posts: 147
Location: Cyprus
Doomer wrote:
you drive has rare heads, check if the heads vendor is marked "alternative" instead of "default" in pc3k rom dialog.
very likely your drive is "alternative" and all the donors are "default".

you'd need correct heads vendor for the donor

I don't have pc3k only MRT and sediv can I get vendor information via terminal? (it doesn't appear in the Ctrl + l command).
Is there preamp type in addition to c2 87 82 ?

Thanks
Top
 Profile  
 
Jirbun
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:13 
Offline

Joined: February 1st, 2016, 19:51
Posts: 147
Location: Cyprus
This "pc3k rom dialog" gives details about rom in boot code?
Top
 Profile  
 
Doomer
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:26 
Offline
User avatar

Joined: September 29th, 2005, 12:02
Posts: 3577
Location: Chicago
Jirbun wrote:
This "pc3k rom dialog" gives details about rom in boot code?

it works with flash ROM file

_________________
SAN, NAS, RAID, Server, and HDD Data Recovery.
Top
 Profile  
 
Amarbir[CDR-Labs]
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:31 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3522
Location: CDRLabs @ Chandigarh [ India ]
Jirbun wrote:
Amarbir[CDR-Labs] wrote:
Hi,
I had a similiar case with 4TB hdd ,The issue was the smart a@#@# data recovery technician before me had headmap to 00 00 00 00 04 04 040 04 lol .Disable Media Cache For The Time Being And Try And Also Check Headmap in ROM

Head map are correct.
Drive ID with capacity -1 (8796093022208.00 GB) in this state it is not possible to perform any action so I can't disable Media Cache.
I changed one bit at offset 802F6(SAP 2F6) from 89 to 09 and it stop click but can't ID.
Besides I found that 99% of sap you can take from donor and somehow to get access to the drive only 1% need to be original in this case I have a problem with that 1%.

Thanks


Well,
Sys file 0x93 has This And Surely in PC3K We can disable whatever we need to

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com
Top
 Profile  
 
Amarbir[CDR-Labs]
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:34 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3522
Location: CDRLabs @ Chandigarh [ India ]
Doomer wrote:
you drive has rare heads, check if the heads vendor is marked "alternative" instead of "default" in pc3k rom dialog.
very likely your drive is "alternative" and all the donors are "default".

you'd need correct heads vendor for the donor


Well,
Is PC3K Not capable in giving us exact preamp that its reverting to Default and Alternative Like Words

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com
Top
 Profile  
 
Doomer
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:35 
Offline
User avatar

Joined: September 29th, 2005, 12:02
Posts: 3577
Location: Chicago
Jirbun wrote:
I changed one bit at offset 802F6(SAP 2F6) from 89 to 09 and it stop click but can't ID.

Just find a donor that has this bit.
It is not an easy find though.

You also can use microscope to check the sliders, they will be different on the original and donors that you used.

_________________
SAN, NAS, RAID, Server, and HDD Data Recovery.


Last edited by Doomer on August 3rd, 2023, 23:37, edited 1 time in total.

Top
 Profile  
 
Doomer
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:36 
Offline
User avatar

Joined: September 29th, 2005, 12:02
Posts: 3577
Location: Chicago
Jirbun wrote:
Is there preamp type in addition to c2 87 82 ?

Thanks

No, there are only three
But your problem is not the preamp.

_________________
SAN, NAS, RAID, Server, and HDD Data Recovery.
Top
 Profile  
 
Amarbir[CDR-Labs]
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:37 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3522
Location: CDRLabs @ Chandigarh [ India ]
gps31 wrote:
Which bit u changed? u may try Virtual boot MRT


Well,
VB Is Not a Solution for Any and Every Issue of Seagate .Whats your experience ,I just updated to Version 218X and i feel MRT Does a Fair Enough Job ,DE Really Needs To Be Update Though Its Too Basic

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com
Top
 Profile  
 
Amarbir[CDR-Labs]
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:38 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3522
Location: CDRLabs @ Chandigarh [ India ]
Doomer wrote:
Jirbun wrote:
Is there preamp type in addition to c2 87 82 ?

Thanks

No, there are only three
But your problem is not the preamp.


Sir ,
Whats the problem according to you in this case

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com
Top
 Profile  
 
Doomer
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:42 
Offline
User avatar

Joined: September 29th, 2005, 12:02
Posts: 3577
Location: Chicago
Amarbir[CDR-Labs] wrote:

Sir ,
Whats the problem according to you in this case

I already answered that
Quote:
your drive has rare heads, check the heads vendor

_________________
SAN, NAS, RAID, Server, and HDD Data Recovery.
Top
 Profile  
 
Doomer
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 3rd, 2023, 23:47 
Offline
User avatar

Joined: September 29th, 2005, 12:02
Posts: 3577
Location: Chicago
Jirbun wrote:
MRT virtual output:

TCC:0023
[LBA=0x00000001][LBA=0x00000001]
RECOV Servo Op=06DF Resp=0005
DSC PASS
RECOV Servo Op=0095 Resp=0005
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=0000000000000001 Duration=00000607 ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DA01][LBA=0x0000DA01]
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=000000000000DA01 Duration=00000048 ms
RECOV Servo Op=0095 Resp=0005[LBA=0x00000406][LBA=0x00000406]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=0000000000000406 Duration=00000047 ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DE06][LBA=0x0000DE06]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=000000000000DE06 Duration=00000046 ms

Change the bit back, the drive won't read any data anyway, only servo.
You can't trick the drive like this unfortunately. You have to have correct heads.

_________________
SAN, NAS, RAID, Server, and HDD Data Recovery.
Top
 Profile  
 
Amarbir[CDR-Labs]
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 4th, 2023, 1:37 
Offline
User avatar

Joined: August 15th, 2006, 3:01
Posts: 3522
Location: CDRLabs @ Chandigarh [ India ]
Doomer wrote:
Jirbun wrote:
MRT virtual output:

TCC:0023
[LBA=0x00000001][LBA=0x00000001]
RECOV Servo Op=06DF Resp=0005
DSC PASS
RECOV Servo Op=0095 Resp=0005
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=0000000000000001 Duration=00000607 ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DA01][LBA=0x0000DA01]
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=000000000000DA01 Duration=00000048 ms
RECOV Servo Op=0095 Resp=0005[LBA=0x00000406][LBA=0x00000406]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=0000000000000406 Duration=00000047 ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DE06][LBA=0x0000DE06]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=000000000000DE06 Duration=00000046 ms

Change the bit back, the drive won't read any data anyway, only servo.
You can't trick the drive like this unfortunately. You have to have correct heads.



Well,
Wise Man Wise Advise Thanks Doomer Sir :please:

_________________
Regards
Amarbir S Dhillon , Chandigarh Data Recovery Labs [India]
Logical,Semi Physical And Physical Data Recovery
Website-> http://www.chandigarhdatarecovery.com
Top
 Profile  
 
Jirbun
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 4th, 2023, 9:20 
Offline

Joined: February 1st, 2016, 19:51
Posts: 147
Location: Cyprus
Doomer wrote:
Jirbun wrote:
MRT virtual output:

TCC:0023
[LBA=0x00000001][LBA=0x00000001]
RECOV Servo Op=06DF Resp=0005
DSC PASS
RECOV Servo Op=0095 Resp=0005
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=0000000000000001 Duration=00000607 ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DA01][LBA=0x0000DA01]
SIM FileFD=FC000000 ErrorCode=43160080 DiscLBA=000000000000DA01 Duration=00000048 ms
RECOV Servo Op=0095 Resp=0005[LBA=0x00000406][LBA=0x00000406]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=0000000000000406 Duration=00000047 ms
RECOV Servo Op=0195 Resp=0005[LBA=0x0000DE06][LBA=0x0000DE06]
SIM FileFD=FC00320D ErrorCode=43160080 DiscLBA=000000000000DE06 Duration=00000046 ms

Change the bit back, the drive won't read any data anyway, only servo.
You can't trick the drive like this unfortunately. You have to have correct heads.

Change the bit back so "Fail servo" drive clicks with all three preamp types.


Last edited by Jirbun on August 4th, 2023, 9:27, edited 1 time in total.

Top
 Profile  
 
Jirbun
 Post subject: Re: ST1000LM035 rosewood clicking after replace many new hea
PostPosted: August 4th, 2023, 9:27 
Offline

Joined: February 1st, 2016, 19:51
Posts: 147
Location: Cyprus
Doomer wrote:
Jirbun wrote:
I changed one bit at offset 802F6(SAP 2F6) from 89 to 09 and it stop click but can't ID.

Just find a donor that has this bit.
It is not an easy find though.

You also can use microscope to check the sliders, they will be different on the original and donors that you used.

Here is the rom if you can write it to your donor and turn it on for half a second to see if donor clicks.
If not,then please PM me a quote for donor.

Thanks


Attachments:
RO orgi.rar [262.68 KiB]
Downloaded 337 times
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 23 posts ]  Go to page 1, 2  Next

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: Google [Bot] and 26 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group