MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Switch to mobile style


Post new topic Reply to topic  Page 1 of 1
  [ 7 posts ] 
  Previous topic | Next topic 
Author Message
Murtazah
 Post subject: Rosewood ST1000LM035-1RK172 Stays BSY after getting ready
PostPosted: September 1st, 2023, 9:15 
Offline

Joined: March 9th, 2012, 7:02
Posts: 49
Location: Dubai
Hello,

This rosewood drive gets ready but goes to BSY as soon as I try to access any sector.

below is terminal output.

Code:
(P) SATA Reset

RAW OFF
PASS
Drive AMPS Configuration has been modified from compiled defaults.
Drive must be re-initialized to controller firmware defaults by re-downloading controller firmware
DO NOT SHIP WITHOUT FIRST RE-DOWNLOADING CONTROLLER FIRMWARE OR RESETTING TO DEFAULTS!

(DOS Table) Worst Count: 00000FFA At SU: 0000531D NT: 00000000 OT: 00000020
MSP213
(MC POR Duration): 0000000045
PrgF
PrgF
Intel 6G->3G
Send Status: COMRESET seen
CSpd= 3Gbps
DSC
Common path start quit now ProcessRC: 00000000,00000000SkipLen: 00000000ReadContinuous: 0E06D933,00000322UnrecovSectorCount:00D7,0321,0042NumUDEs: 000000D7,00000003,00000321Passed: 00000080,00000140,000002D1Out:
PE  43110081
PrgF
LED:0x000000EE FAddr:0x004E6CE0

LED:0x000000EE FAddr:0x004E6CE0

LED:0x000000EE FAddr:0x004E6CE0


I have got all the important modules backedup. Also when I try to write updated 93 in indirect ATA mode it gets bsy and fails.

Kindly advise.

_________________
Best Regards,
Murtaza H.
Data Recovery Dubai
Top
 Profile  
 
pepe
 Post subject: Re: Rosewood ST1000LM035-1RK172 Stays BSY after getting read
PostPosted: September 1st, 2023, 13:59 
Offline

Joined: October 3rd, 2005, 0:40
Posts: 4753
Location: Hungary
is that the full log? what happens before the SATA Reset?

_________________
Adatmentés - Data recovery
Top
 Profile  
 
Murtazah
 Post subject: Re: Rosewood ST1000LM035-1RK172 Stays BSY after getting read
PostPosted: September 1st, 2023, 15:04 
Offline

Joined: March 9th, 2012, 7:02
Posts: 49
Location: Dubai
this is the terminal output if I dont press Ctrl+Z for Terminal Prompt.
Code:
Boot 0x80M
Tech Unlock Handshake: 0x33EFD0C9
Reply:
QB
Rst 0x80MSrv ETCR init 0x0000
PrgF
(P) SATA Reset

RAW OFF
PASS
Drive AMPS Configuration has been modified from compiled defaults.
Drive must be re-initialized to controller firmware defaults by re-downloading controller firmware
DO NOT SHIP WITHOUT FIRST RE-DOWNLOADING CONTROLLER FIRMWARE OR RESETTING TO DEFAULTS!

(DOS Table) Worst Count: 00000FFA At SU: 0000531D NT: 00000000 OT: 00000020
MSP213
(MC POR Duration): 0000000045
PrgF
Intel 6G->3G
Send Status: COMRESET seen
CSpd= 3Gbps
DSC
Common path start quit now ProcessRC: 00000000,00000000SkipLen: 00000000ReadContinuous: 0E06D933,00000322UnrecovSectorCount:00D9,0321,0042NumUDEs: 000000D9,00000023,00000321Passed: 00000080,00000140,000002D1Out:
PE  43110081
PrgF
LED:0x000000EE FAddr:0x004E6CE0

LED:0x000000EE FAddr:0x004E6CE0

LED:0x000000EE FAddr:0x004E6CE0

LED:0x000000EE FAddr:0x004E6CE0




And this, If after handshake I press Ctrl + Z for Terminal Prompt.

Code:
Boot 0x80M
Tech Unlock Handshake: 0x380EF2B7
Reply:
QB
Rst 0x80MSrv ETCR init 0x0000
PrgF
(P) SATA Reset

RAW OFF
PASS
Drive AMPS Configuration has been modified from compiled defaults.
Drive must be re-initialized to controller firmware defaults by re-downloading controller firmware
DO NOT SHIP WITHOUT FIRST RE-DOWNLOADING CONTROLLER FIRMWARE OR RESETTING TO DEFAULTS!

(DOS Table) Worst Count: 00000FFA At SU: 0000531D NT: 00000000 OT: 00000020
MSP213
(MC POR Duration): 0000000045
PrgF
Intel 6G->3G
Send Status: COMRESET seen
CSpd= 3Gbps
DSC
ASCII Diag mode

F3 T>
Input_Command_Error

F3 T>
ASCII Diag mode

F3 T>
Input_Command_Error

F3 T>
ASCII Diag mode

F3 T>
Input_Command_Error

F3 T>

_________________
Best Regards,
Murtaza H.
Data Recovery Dubai
Top
 Profile  
 
pepe
 Post subject: Re: Rosewood ST1000LM035-1RK172 Stays BSY after getting read
PostPosted: September 1st, 2023, 17:48 
Offline

Joined: October 3rd, 2005, 0:40
Posts: 4753
Location: Hungary
where did the LED EE disappeared? now it doesn't happen?

_________________
Adatmentés - Data recovery
Top
 Profile  
 
Murtazah
 Post subject: Re: Rosewood ST1000LM035-1RK172 Stays BSY after getting read
PostPosted: September 2nd, 2023, 1:10 
Offline

Joined: March 9th, 2012, 7:02
Posts: 49
Location: Dubai
It does not show LED EE if I enter the terminal prompt. If I dont press CTRL + Z then it shows LED Error after about every 40 to 50 seconds.

_________________
Best Regards,
Murtaza H.
Data Recovery Dubai
Top
 Profile  
 
pepe
 Post subject: Re: Rosewood ST1000LM035-1RK172 Stays BSY after getting read
PostPosted: September 2nd, 2023, 4:57 
Offline

Joined: October 3rd, 2005, 0:40
Posts: 4753
Location: Hungary
ic. Can you post ROM and sysfiles 0_20D, 0_20E (if already read)?
pepe

_________________
Adatmentés - Data recovery
Top
 Profile  
 
Murtazah
 Post subject: Re: Rosewood ST1000LM035-1RK172 Stays BSY after getting read
PostPosted: September 2nd, 2023, 5:23 
Offline

Joined: March 9th, 2012, 7:02
Posts: 49
Location: Dubai
please find attached.


Attachments:
ROM-20D-20E.zip [2.33 MiB]
Downloaded 141 times

_________________
Best Regards,
Murtaza H.
Data Recovery Dubai
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 7 posts ] 

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: Google [Bot] and 30 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group