MultiDrive – free backup, clone & wipe disk utility from Atola Technology

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 
  Previous topic | Next topic 
Author Message
crystalrajasthan
 Post subject: ST500DM002....Cannot access the terminal
PostPosted: July 16th, 2014, 4:45 
Offline

Joined: October 8th, 2012, 5:29
Posts: 44
Location: India
I have 2 Seagate Sata ST500DM002 hdd, both the hdd spins normal but cannot access the terminal. Even I try to short pin point also ....it shows the following message as show below after shorting :-

Boot 0x10M
Spin Up[0x00000000][0x00000000]ZZZZMMMMMMMMMMMMMMMZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMddddddWYWYWWMMMMMM
FAIL Servo Op=0155 Resp=0007
ResponseFrame 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 000Ax[0x00025CB4][0x00025CB4]ZZZZMMMMMMMMMMMMMMMZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMddddddWWWWMMMMMM
FAIL Servo Op=0055 Resp=0007
ResponseFrame 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 000Ax[0x0000B319][0x0000B319]ZZZZMMMMMMMMMMMMMMMZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMddddddWYWYWWMMMMMM
FAIL Servo Op=0155 Resp=0007
ResponseFrame 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 000Ax[0x00030FCD][0x00030FCD]ZZZZMMMMMMMMMMMMMMMZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMMddddddWWWWMMMMMM
FAIL Servo Op=0055 Resp=0007
ResponseFrame 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 000Ax


Any help appreciated....
Top
 Profile  
 
hhddrec
 Post subject: Re: ST500DM002....Cannot access the terminal
PostPosted: July 16th, 2014, 5:40 
Offline
User avatar

Joined: August 13th, 2008, 13:10
Posts: 811
Location: World
Can you report us more info about HDD.
FW, ROM, PCB info too
symptomps about HDD, clicking sounds, the drive starts spining, and oter data.

Maybe posible that you can send HDD sticker pics and PCB both sides pics.

Data is important? or maybe not important?
thanks
Top
 Profile  
 
labtech
 Post subject: Re: ST500DM002....Cannot access the terminal
PostPosted: July 16th, 2014, 8:50 
Offline

Joined: August 18th, 2010, 17:35
Posts: 3669
Location: Massachusetts, USA
High chance it is a problem with the terminal set up. What is your hardware and software terminal set up?

_________________
Hard Disk Drive (HDD), Solid State Drive (SSD, SATA, NVMe, etc), USB Flash Drive and RAID Data Recovery Specialist in Massachusetts
Top
 Profile  
 
crystalrajasthan
 Post subject: Re: ST500DM002....Cannot access the terminal
PostPosted: July 17th, 2014, 4:41 
Offline

Joined: October 8th, 2012, 5:29
Posts: 44
Location: India
Hd spin normally, no strange sound only terminal is not accessable, as we are using PC3K
I contact to ACE support but they said, short the pin point.....still hdd is not getting ready
Data is important.
Mdl=ST500DM002
FW=KC45
PCB No=100535704 REV C
Top
 Profile  
 
hhddrec
 Post subject: Re: ST500DM002....Cannot access the terminal
PostPosted: July 17th, 2014, 5:00 
Offline
User avatar

Joined: August 13th, 2008, 13:10
Posts: 811
Location: World
Are you sure that you terminal is in good condition?

test it with other working similar HDD
Top
 Profile  
 
crystalrajasthan
 Post subject: Re: ST500DM002....Cannot access the terminal
PostPosted: July 17th, 2014, 5:07 
Offline

Joined: October 8th, 2012, 5:29
Posts: 44
Location: India
I have checked with other working hdd, terminal is properly working.....
Hdd have some strange problem and I have 2 of them.....
Top
 Profile  
 
MindMergepk
 Post subject: Re: ST500DM002....Cannot access the terminal
PostPosted: July 17th, 2014, 7:23 
Offline
User avatar

Joined: December 8th, 2013, 4:48
Posts: 838
Location: Pakistan
did hard drive report his model and capacity correctly in PC3K ?

_________________
Data Recovery Pakistan
Top
 Profile  
 
Nick_CT
 Post subject: Re: ST500DM002....Cannot access the terminal
PostPosted: July 17th, 2014, 7:24 
Offline
User avatar

Joined: September 5th, 2010, 12:29
Posts: 1038
Location: South Africa
Are you sure you are shorting the correct points at the correct time?

_________________
Death is nothing, but to live defeated and inglorious is to die daily.
Data Recovery Cape Town
Top
 Profile  
 
crystalrajasthan
 Post subject: Re: ST500DM002....Cannot access the terminal
PostPosted: July 17th, 2014, 8:04 
Offline

Joined: October 8th, 2012, 5:29
Posts: 44
Location: India
No hdd stay only busy and I am shorting right points......
Top
 Profile  
 
msurgeon
 Post subject: Re: ST500DM002....Cannot access the terminal
PostPosted: July 17th, 2014, 15:48 
Offline

Joined: August 14th, 2008, 10:39
Posts: 257
Location: Morris Plains, New Jersey
This takes some finesse. Wait for the second "spin-up" message in terminal then short the points. Keep shorting the points for a few seconds; remove short. Terminal output will continue for a few minutes and then stop. Drive should then be ready. These drives do not spin down during the procedure but they will come ready if your technique is good. Patience.
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 10 posts ] 

Main » Forums home » Conventional hard drives

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: jimmydata and 101 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Switch to mobile style
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group