Rosewood ST1000LM035-1RK172 Stays BSY after getting ready

Hello,

This rosewood drive gets ready but goes to BSY as soon as I try to access any sector.

below is terminal output.

Code:: (P) SATA Reset RAW OFF PASS Drive AMPS Configuration has been modified from compiled defaults. Drive must be re-initialized to controller firmware defaults by re-downloading controller firmware DO NOT SHIP WITHOUT FIRST RE-DOWNLOADING CONTROLLER FIRMWARE OR RESETTING TO DEFAULTS! (DOS Table) Worst Count: 00000FFA At SU: 0000531D NT: 00000000 OT: 00000020 MSP213 (MC POR Duration): 0000000045 PrgF PrgF Intel 6G->3G Send Status: COMRESET seen CSpd= 3Gbps DSC Common path start quit now ProcessRC: 00000000,00000000SkipLen: 00000000ReadContinuous: 0E06D933,00000322UnrecovSectorCount:00D7,0321,0042NumUDEs: 000000D7,00000003,00000321Passed: 00000080,00000140,000002D1Out: PE 43110081 PrgF LED:0x000000EE FAddr:0x004E6CE0 LED:0x000000EE FAddr:0x004E6CE0 LED:0x000000EE FAddr:0x004E6CE0

I have got all the important modules backedup. Also when I try to write updated 93 in indirect ATA mode it gets bsy and fails.

Kindly advise.

is that the full log? what happens before the SATA Reset?

this is the terminal output if I dont press Ctrl+Z for Terminal Prompt.

Code:: Boot 0x80M Tech Unlock Handshake: 0x33EFD0C9 Reply: QB Rst 0x80MSrv ETCR init 0x0000 PrgF (P) SATA Reset RAW OFF PASS Drive AMPS Configuration has been modified from compiled defaults. Drive must be re-initialized to controller firmware defaults by re-downloading controller firmware DO NOT SHIP WITHOUT FIRST RE-DOWNLOADING CONTROLLER FIRMWARE OR RESETTING TO DEFAULTS! (DOS Table) Worst Count: 00000FFA At SU: 0000531D NT: 00000000 OT: 00000020 MSP213 (MC POR Duration): 0000000045 PrgF Intel 6G->3G Send Status: COMRESET seen CSpd= 3Gbps DSC Common path start quit now ProcessRC: 00000000,00000000SkipLen: 00000000ReadContinuous: 0E06D933,00000322UnrecovSectorCount:00D9,0321,0042NumUDEs: 000000D9,00000023,00000321Passed: 00000080,00000140,000002D1Out: PE 43110081 PrgF LED:0x000000EE FAddr:0x004E6CE0 LED:0x000000EE FAddr:0x004E6CE0 LED:0x000000EE FAddr:0x004E6CE0 LED:0x000000EE FAddr:0x004E6CE0

And this, If after handshake I press Ctrl + Z for Terminal Prompt.

Code:: Boot 0x80M Tech Unlock Handshake: 0x380EF2B7 Reply: QB Rst 0x80MSrv ETCR init 0x0000 PrgF (P) SATA Reset RAW OFF PASS Drive AMPS Configuration has been modified from compiled defaults. Drive must be re-initialized to controller firmware defaults by re-downloading controller firmware DO NOT SHIP WITHOUT FIRST RE-DOWNLOADING CONTROLLER FIRMWARE OR RESETTING TO DEFAULTS! (DOS Table) Worst Count: 00000FFA At SU: 0000531D NT: 00000000 OT: 00000020 MSP213 (MC POR Duration): 0000000045 PrgF Intel 6G->3G Send Status: COMRESET seen CSpd= 3Gbps DSC ASCII Diag mode F3 T> Input_Command_Error F3 T> ASCII Diag mode F3 T> Input_Command_Error F3 T> ASCII Diag mode F3 T> Input_Command_Error F3 T>

where did the LED EE disappeared? now it doesn't happen?

It does not show LED EE if I enter the terminal prompt. If I dont press CTRL + Z then it shows LED Error after about every 40 to 50 seconds.

ic. Can you post ROM and sysfiles 0_20D, 0_20E (if already read)?
pepe

please find attached.

Attachments

Re: Rosewood ST1000LM035-1RK172 Stays BSY after getting read