WD1200JB-00FUA0

[zebong]

Hello

Have a disk with this when i connect :
It can not show-me the SA FW Version
Anyone have this error ?


Techno mode key:
HDD geometry loading.................... : Ok
Cyl Count............................... : 81004
Head Count.............................. : 4
SPT..................................... : 900

RAM:
Zone allocation table................... : Ok
ROM version............................. : 15.BE.
SA FW version........................... : ......
Link table version...................... : 05.66.

Serial ROM:
Read ROM................................ : Ok
Heads configuration..................... : From map
Heads number............................ : 6
The number of heads in use.............. : 4
Disabled heads.......................... : Yes
Head map................................ : 0,1,4,5

Service area:
Modules table loading................... : Drive is not ready
Configuration loading................... : WD Techno Key Error Drive is not ready
Translation overlay checking (Copy 0)... : Not found in modules directory
Translation overlay checking (Copy 1)... : Not found in modules directory

Thanks
ZeBong

[pcimage]

What about the modules?

Can you read/check them?

[networkpc3000]

i think i have idea to find out which version it's.

[zebong]

What about the modules?

Can you read/check them?

i can not read them, it appear blank.

i also try to cut head by head but nothing happen.

[zebong]

i think i have idea to find out which version it's.

So what do you think it is ?

[Mikippp]

Hi,

Modules table loading................... : Drive is not ready

Modules table NOT loaded!!! (module 41.rpm [~Dir.rpm])
At first Read (backup) all service tracks...

Mikippp

[zebong]

hi,

that´s the problem i can not see any module and i can not backup

[Mikippp]

At first Read (backup) all service tracks... (tracks not modules)
You can not read modules becouse modules table was NOT loaded!!!
Then read the manual... especially informations about module "ID=41h" and about "Utility extensions".

Mikippp

[zebong]

Thanks,

i go there and i dont see any backup off tracks.

ZeBong

Attachments

[rameez]

Its in the test menu .

[zebong]

Hi try to make the backup off the tracks:

But i can not, what do you think the problem is :

Thanks


Reading service tracks
Into folder............................. : <HDD Profile>\Data\Tracks
Reading heads........................... : 0,1,4,5
WD Techno Read Error C/H/S: -1/0/0
WD Techno Read Error C/H/S: -1/0/1
Cyl -1; Head 0.......................... : Break
WD Techno Read Error C/H/S: -1/1/0
WD Techno Read Error C/H/S: -1/1/1
WD Techno Read Error C/H/S: -1/1/2
WD Techno Read Error C/H/S: -1/1/3
WD Techno Read Error C/H/S: -1/1/4
Cyl -1; Head 1.......................... : Break

[Mikippp]

Hi,
You use original PCB with original ROM ?
Did you try the head check?
wd1200bb-changed-rom-and-pcb-still-not-work-t7717.html

Mikippp

[zebong]

Hi,
You use original PCB with original ROM ?
Did you try the head check?
wd1200bb-changed-rom-and-pcb-still-not-work-t7717.html

Mikippp

Yes,

Everything is original.

[rameez]

I think problem with head 1 .

[zebong]

Anyone have one disk to seel need the heads match

WD1200JB-00FUA0

ZeBong

[harddrivespecialist]

Do you need a drive to work with a drive discussed above?

[zebong]

Hello,

This things happen today i turn on the disk and it can be detect byt the udma.

Techno mode key:
HDD geometry loading.................... : Ok
Cyl Count............................... : 15468
Head Count.............................. : 4
SPT..................................... : 900

RAM:
Zone allocation table................... : Ok
ROM version............................. : 15.BE.
SA FW version........................... : 15.BER
Link table version...................... : 05.66.

Serial ROM:
Read ROM................................ : Ok
Heads configuration..................... : From map
Heads number............................ : 6
The number of heads in use.............. : 4
Disabled heads.......................... : Yes
Head map................................ : 0,1,4,5

Service area:
Modules table loading................... : Ok (Copy 0)
Configuration loading................... : Ok
Master Password......................... : has not been set
User Password........................... : has not been set
Translation overlay checking............ : Ok


Also i start to make a copy with DE but it give ecc error,
Anyone can help on this ?

Thanks
ZeBong

[harddrivespecialist]

You have to read it by head map and read the ones that do read and then work with the ones that don't read.

[zebong]

You have to read it by head map and read the ones that do read and then work with the ones that don't read.

Try to build a head maps but it give error.

[zebong]

Make a head test :

it gives OK,

Heads test
Cylinder to test........................ : -25
Heads to test........................... : 0,1,2,3
Head 0.................................. : Ok
Head 1.................................. : Ok
Head 4.................................. : Ok
Head 5.................................. : Ok



SA surface verification
Initial cylinder........................ : -1
Final cylinder.......................... : -20
Head.................................... : 0,1
Cyl -1 Head 0........................... : Errors : 0
Cyl -1 Head 1........................... : Errors : 0
Cyl -2 Head 0........................... : Errors : 0
Cyl -2 Head 1........................... : Errors : 0
Cyl -3 Head 0........................... : Errors : 0
Cyl -3 Head 1........................... : Errors : 0
Cyl -4 Head 0........................... : Errors : 0
Cyl -4 Head 1........................... : Errors : 0
Cyl -5 Head 0........................... : Errors : 0
Cyl -5 Head 1........................... : Errors : 0
Cyl -6 Head 0........................... : Errors : 0
Cyl -6 Head 1........................... : Errors : 0
Cyl -7 Head 0........................... : Errors : 0
Cyl -7 Head 1........................... : Errors : 0
Cyl -8 Head 0........................... : Errors : 2
--------------------------------------------------
Sectors :Error
--------------------------------------------------
304.....................................
319.....................................
--------------------------------------------------
Cyl -8 Head 1........................... : Errors : 0
Cyl -9 Head 0........................... : Errors : 0
Cyl -9 Head 1........................... : Errors : 0
Cyl -10 Head 0.......................... : Errors : 0
Cyl -10 Head 1.......................... : Errors : 0
Cyl -11 Head 0.......................... : Errors : 0
Cyl -11 Head 1.......................... : Errors : 0
Cyl -12 Head 0.......................... : Errors : 0
Cyl -12 Head 1.......................... : Errors : 0
Cyl -13 Head 0.......................... : Errors : 0
Cyl -13 Head 1.......................... : Errors : 0
Cyl -14 Head 0.......................... : Errors : 0
Cyl -14 Head 1.......................... : Errors : 0
Cyl -15 Head 0.......................... : Errors : 0
Cyl -15 Head 1.......................... : Errors : 0
Cyl -16 Head 0.......................... : Errors : 0
Cyl -16 Head 1.......................... : Errors : 0
Cyl -17 Head 0.......................... : Errors : 0
Cyl -17 Head 1.......................... : Errors : 0
Cyl -18 Head 0.......................... : Errors : 0
Cyl -18 Head 1.......................... : Errors : 0
Cyl -19 Head 0.......................... : Errors : 0
Cyl -19 Head 1.......................... : Errors : 0
Cyl -20 Head 0.......................... : Errors : 16
--------------------------------------------------
Sectors :Error
--------------------------------------------------
1.......................................
11......................................
15 -- 16................................
20 -- 21................................
25 -- 26................................
30 -- 31................................
35 -- 36................................
40 -- 41................................
45 -- 46................................
--------------------------------------------------
Cyl -20 Head 1.......................... : Errors : 24
--------------------------------------------------
Sectors :Error
--------------------------------------------------
1.......................................
10 -- 11................................
15 -- 16................................
17......................................Drive is not ready
20 -- 21................................
22......................................Drive is not ready
25 -- 26................................
27......................................Drive is not ready
30 -- 31................................
32......................................Drive is not ready
35 -- 36................................
37......................................Drive is not ready
40 -- 41................................
42......................................Drive is not ready
45 -- 46................................
47......................................Drive is not ready
--------------------------------------------------

SA surface verification completed