Hi,

I dont see alot of Samsung drives in my shop so they are a bit on the side with me...

I got this Samsung model HM251HX(USB), when connected with USB cable spins up just fine no clicking sound and stays spining. There is no detection on USB and with terminal i get this:

 U
S_0Shock Sensor Circuit Enabled
SO_1
Shock Sensor Circuit Enabled
IS=5
CLA #36/47
Handoff RPM=686
SPOK
mS1 00000003
A1O=120 A1G=449
O=509 S=2
SK C: 5062 H:0
POK
POK
Boot Sector Error! Take a default.
Loaded FIT ( 0: 0: 1)
| 4 | MLIST | 0 | 0 | 10 | B98A |
| 4 | MLIST | 0 | 1 | 10 | B98A |
| 4 | MLIST | 33 | 0 | 10 | B98A |
| 4 | MLIST | 33 | 1 | 10 | B98A |
| 155 | SV_TBL | 0 | 0 | 23 | B98A |
| 155 | SV_TBL | 0 | 1 | 23 | B98A |
| 155 | SV_TBL | 33 | 0 | 23 | B98A |
| 155 | SV_TBL | 33 | 1 | 23 | B98A |
| 181 | RESO_TBL | 0 | 0 | 35 | B98A |
| 181 | RESO_TBL | 0 | 1 | 35 | B98A |
file system read bad
Bump Limit Loaded. Rev:0x00
| 180 | RR0_TBL | 0 | 0 | 33 | B98A |
| 180 | RR0_TBL | 0 | 1 | 33 | B98A |
| 180 | RR0_TBL | 33 | 0 | 33 | B98A |
| 180 | RR0_TBL | 33 | 1 | 33 | B98A |
[CAN'T READ RRO]
| 12 | CHN_TBL | 0 | 0 | 41 | B98A |
| 12 | CHN_TBL | 0 | 1 | 41 | B98A |
| 12 | CHN_TBL | 33 | 0 | 41 | B98A |
| 12 | CHN_TBL | 33 | 1 | 41 | B98A |
| 13 | GEO_TBL | 0 | 0 | 115 | B98A |
| 13 | GEO_TBL | 0 | 1 | 115 | B98A |
| 13 | GEO_TBL | 33 | 0 | 115 | B98A |
| 13 | GEO_TBL | 33 | 1 | 115 | B98A |
Ovly (0x0001CD00) chksum fail!
Ovly (0x1005B800) chksum fail!
Ovly NOT loaded
| 164 | TU^E_RST | 0 | 0 | 193 | B98B |
| 164 | TU^E_RST | 0 | 1 | 193 | B98B |
| 104 | FDT_TBL | 0 | 0 | 36 | B98A |
| 104 | FDT_TBL | 0 | 1 | 36 | B98A |
| 104 | FDT_TBL | 33 | 0 | 36 | B98A |
| 104 | FDT_TBL | 33 | 1 | 36 | B98A |
file system read bad
| 105 | SCRAMBER | 0 | 0 | 210 | B98A |
Reading Serial Num Pass
Up MC

PwrOn RRO1x @ H0
Table) cos = 0, sin = 0
Coeff) cos = -482798, sin = -79537

DiskSlip : 0 [SrvTrk]
DiskSlip : 45 [SrvTrk]
TgtCyl: 842
Hd: 0 Zn: 0 Avg.:- 42
TgtCyl: 169830
Hd: 0 Zn: 1 Avg.: 740

SVCAL(0080,0000)-->PASS
[DEBUG HALT @HAL_SOC_SEG_SetSubSegmentBeginEndHost():0000533B L0 1003CA0F]
POK
Cur_SP=040073E0
FIQ_SP=040073E0
IRQ_SP=040073E0
SVC_SP=040073E0

*** HALT ***

Looks like a firmware problem to me, anyone seen this before?
My next step is bypass USB and direct connect to analyze some more...but i had to ask if someone has seen this before

Question is bothering me is shouldnt USB detect something? Like WD's?

Thanks for any answer!

I see it every week or so...