MultiDrive – free backup, clone & wipe disk utility from Atola Technology

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 11 posts ] 
Author Message
 Post subject: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 3:20 
Offline

Joined: August 3rd, 2012, 7:47
Posts: 396
Location: slovenija
Hello,

I receive drive from customer that report "disk read error".
I image drive to another drive. Everything was OK and job was done OK. It was strange, that Ghost report that copy 476929MB of data. Drive capacity in ghost 476929MB.
When I connect destination drive to computer, it report same error.
I connect drive to working winxp PC over USB dock. Windows detect drive, show drive, but report disk read error. Size in properties is 0.
Is any good SW solution to fix partition and to image full drive.


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 3:33 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 16960
Location: Australia
jerovsek wrote:
It was strange, that Ghost report that copy 476929MB of data. Drive capacity in ghost 476929MB.

Is it a 500GB drive? If so, then why should the reported capacity be strange?

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 3:42 
Offline

Joined: August 3rd, 2012, 7:47
Posts: 396
Location: slovenija
Hello Mr. Zabkar,

it's 500GB drive.
Sorry. Ghost reported size of source and destination is 476940MB
Copied 476929MB


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 3:50 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 16960
Location: Australia
Is the capacity reported differently via the dock compared with a direct SATA connection?

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 4:13 
Offline

Joined: August 3rd, 2012, 7:47
Posts: 396
Location: slovenija
Dear Mr. Zabkar,

I suspect, that something is wrong with partition table. It's strange, that Ghost copy full capacyty of data. Like that the disk is full of data. Normally it show data size on disk.

I can recover files, this is not problem.
But I would like to boot from this drive.

Thank you


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 5:19 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 16960
Location: Australia
Could we see sector 0?

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 5:56 
Offline

Joined: August 3rd, 2012, 7:47
Posts: 396
Location: slovenija
Dear Mr. Zabkar,

sector 0
Attachment:
sector0.jpg
sector0.jpg [ 200.93 KiB | Viewed 6162 times ]


and sector 63
Attachment:
sector63.jpg
sector63.jpg [ 202.2 KiB | Viewed 6162 times ]


Thank you very much


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 6:35 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 16960
Location: Australia
The boot sector is indicating that the NTFS volume begins at sector 63 (= 0x3F) and has a size of 0x3A380D40 sectors.

The partition table has a single NTFS partition beginning at sector 63 and with a size of 0x3A380D41 sectors.

The partition size is ...

0x3a380d41 x 512 bytes = 476929.657 megabytes

I believe there should be a backup NTFS boot sector at sector 0x0x3A380D7F.

In short I can't see any problem.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 8:36 
Offline
User avatar

Joined: August 26th, 2012, 19:18
Posts: 293
Location: England
Quote:
size of source and destination is 476940MB Copied 476929MB

476940MB - 476929MB = 11MB

XP: could ths be down to Cylinder alignment ie XP default is Cyl, and wont use anything less than a full cylinder? or MebiByte v MegaByte?

On an XP machine at the minute and have around 10-11 MB space at the end of a drive.

K

_________________
Когда хочется кушать – съешь всё.
Голод не тётка!


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 16:15 
Offline
User avatar

Joined: September 8th, 2009, 18:21
Posts: 16960
Location: Australia
ISTM that 11MB is a little more than 1 cylinder.

255 heads x 63 sectors/track x 512 bytes/sector = 8 225 280 bytes

However, the partition does end on a cylinder boundary.

0x3A380D80 / 255 / 63 = 0xED80

It still doesn't explain the "disc read error" message, unless the dock is shrinking the physical drive.

_________________
A backup a day keeps DR away.


Top
 Profile  
 
 Post subject: Re: WINXP - disk read error - partition problem
PostPosted: April 17th, 2014, 16:45 
Offline

Joined: August 3rd, 2012, 7:47
Posts: 396
Location: slovenija
Dear digitalferret and Mr. Zabkar,

there is unpartitioned space around 10MB(as digitalferret mentioned).


In Windows Disk management drive is healthy with correct size, but without file system.
Attachment:
mf_winxp_disk.jpg
mf_winxp_disk.jpg [ 81.57 KiB | Viewed 6073 times ]


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: Google [Bot] and 68 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group