Hi hello. Need shorting points to enter safemode on this board.
Details:
Main Cpu MAP1602A Maxio
Nands: 2x Longsys YMTC 232L
Interface nvme.
Here is picture:

_________________
Hello everyone, sorry for my poor english, because i using google translator.

This SSD looks similar:

https://www.igorslab.de/wp-content/uploads/2025/09/SSD-Naked.jpg

There is an SOT23-5 IC to the right of the Maxio controller. I suspect that it provides the VCC supply for the NAND flash. If so, then you could short its enable pin to ground. This will turn off the NAND supply and cause the controller to panic.

If you want to try this, show me a clearer photo of that IC.

_________________
A backup a day keeps DR away.

This is marked ic 8102.
A try make clearly from my phone but all the time picture is not clear.

_________________
Hello everyone, sorry for my poor english, because i using google translator.

https://www.m3tekic.com/filedown.php?file=MT8102_PDS_R0.15_20211209-web.pdf&site=dXBsb2FkLzIwMjIvMDIvMjAyMjAyMTYxNzU4MzYyODIucGRm

If there is a pullup resistor between the EN pin and VIN, then shorting EN to ground should disable the IC. You could short pins 1 and 2 with a DMM probe tip.

_________________
A backup a day keeps DR away.

I try, and nothing, can't detect drive, nothing. This IC is 1.8V for maxio chip, but for nands is PMIC
Marking code
EAEHcH or EAERcH

_________________
Hello everyone, sorry for my poor english, because i using google translator.

I thought it may be a Silergy IC, but EAExyz is an LDO regulator. I tried FAExyz, but couldn't find anything.

_________________
A backup a day keeps DR away.

Yeah, nice. The pcb revision is PCM0002A1727.

_________________
Hello everyone, sorry for my poor english, because i using google translator.

It is FAE:

https://www.comptoir-hardware.com/images/stories/articles/stockage/ssd/lexar/nm790/nm790_face_aoilp.jpg

You could at least determine which test points are connected to ground or the supply rails.

_________________
A backup a day keeps DR away.

I try, find any datasheet for this IC, and can't find any info.

_________________
Hello everyone, sorry for my poor english, because i using google translator.

I normally search for Silergy datasheets as follows:

https://www.google.com/search?q=filetype%3Adoc+OR+filetype%3Apdf+%22absolute+maximum%22+FAExyz+Silergy

Your IC may be a special part that is not available in the retail channel.

_________________
A backup a day keeps DR away.

It would be SY8686K Marking FAExyz but i never seen any datasheet for this IC.
What can i do, to force ROM on this board!?

_________________
Hello everyone, sorry for my poor english, because i using google translator.

SY8686K, Silergy, High Efficiency and High Integration PMIC for SSD System, 3 bucks + 2 LDOs, marking FAExyz, CSP2.42×2.82-36:

https://us1.silergy.com/zh/download/downloadFile?id=6348&type=product&ftype=note

_________________
A backup a day keeps DR away.

Yeah, Great, but as you can see, PMIC supplied SOC in my case SOC is Maxio so if i disable power for SOC this I won't be able to enter ROM mode.

_________________
Hello everyone, sorry for my poor english, because i using google translator.

The trick to enter ROM/safe mode (or ERRMOD) in some Samsung SSDs is to short the I2C clock and data pins. You might try to determine if the I2C pins are present at the test points.

_________________
A backup a day keeps DR away.