Problem with WDC WD400LB-07DNA2 HDD

Hi !
I have problem with WDC WD400LB-07DNA2 HDD...
Drive is detected by BIOS
Configuration sector is readable
DLGDIAG QUICK TEST -> RESULTS - "SMART ERROR"

I think that drive have errors in SA (Firmware errors), but I'm not sure...

Code:: 50 ERR INDX CORR DREQ DRSC WRFT DRDY BUSY AMNF T0NF ABRT IDNF UNCR BBK 00 [WDC WD400LB-07DNA2 ] [ 78,165,360] [ 283,560] [ EST: 2:18:02 ] ţ Smart -> ATT Getting SMART attributes... OK Name Val Worst Raw Att # 1 : Read error rate : 200 1 0 Att # 3 : Spin up time : 87 86 2166 Att # 4 : Number of spin-up times : 96 96 4657 Att # 5 : Reallocated sectors count : 1 1 26906 Att # 7 : Seek error rate : 200 199 0 Att # 9 : Power-on time : 100 100 265 Att # 10 : Spin-up retries : 47 46 12352 Att # 11 : Calibration retries : 100 100 321 Att # 12 : Start/stop count : 100 100 46 Att # 194 : HDA Temperature : 115 253 28 Att # 196 : Reallocate event count : 1 1 4108 Att # 197 : Current pending sectors : 254 200 0 Att # 198 : Offline scan UNC sectors : 199 199 8 Att # 199 : Ultra ATA CRC Error Rate : 200 253 4192 Att # 200 : Write error rate : 200 85 8 ţ Log saved to file: LOG\smart.log | Select a drive : <SHIFT+F3> | 18:51:20

DLGDIAG.LOG

Code:: 09/04/2005, 20:47:04 SELECTED OPTION - "SMART STATUS" SELECTED DRIVE - Model : WDC WD400LB-07DNA2 S/N : WD-WMADY12***** Firmware : 79.07B79 C H S : 77545 16 63 Capacity : 40.0G Drive : 0 Port: 0x170 RESULTS - "SMART ERROR" ERROR/STATUS CODE = 0159

Code:: 59 ERR INDX CORR DREQ DRSC WRFT DRDY BUSY AMNF T0NF ABRT IDNF UNCR BBK 10 [WDC WD400LB-07DNA2 ] [ 78,165,360] [ ] [ ] Supports: LBA48 HPA AAM DLMC LBA MS16 DMA (UDMA5,MWDMA2) SMART: Enabled SelfTest: Supported ErrorLog: Supported Security: high, OFF. Size = 38166MB MHDD>.wd MHDD ATA/SCSI TERMINAL v2.1 Script: WD ************************************************************* ţ Reset... ţ Reading Configuration Sector ű Configuration Sector (wd.bin) has been written MHDD>.test MHDD ATA/SCSI TERMINAL v2.1 Script: TEST ************************************************************* ţ Simple test script ţ Reset... ţ Getting identify information ű identify.bin has been written ţ Reading 100 sectors starting from LBA 0 ERROR: Look at the registers | Take a screenshot : <F10> | 19:03:12

Rewraite 44 and 25 modules from other HDD and afterwards clean Glist
Afterwards - format its...
If in 25 modules were not brought tracks from SA, that you carrying

it's problem in translator. use pc-3000 and regenerate translator. empty g-list, don't write module.

http://www.yudiharddisk.com

yudi wrote:it's problem in translator. use pc-3000 and regenerate translator. empty g-list, don't write module.

No, it's not a translator problem. Some of the SMART modules are damaged. Find and fix them.

No, it's not a translator problem. Some of the SMART modules are damaged. Find and fix them.[/quote]

ok, sory i am wrong.

Hello,

from the smart attributes log it is obvious that Glist is full.
I would empty Glist and zero fill the drive and see if it still contain bads.

regards,
pepe

pepe wrote:Hello,

from the smart attributes log it is obvious that Glist is full.
I would empty Glist and zero fill the drive and see if it still contain bads.

regards,
pepe

Even if you empty the G-list Smart will report bad. That is why you have to rewrite Smart table with a good one!

Hi,
Can anybody send me modules 25 and 44 for this HDD (WD400LB-07DNA2)
PZU: 79.06.
SA FW: 79.06B.
TS: 07.4D.

Mikippp